diff options
Diffstat (limited to 'OSX')
| -rw-r--r-- | OSX/README.txt | 1074 |
1 files changed, 543 insertions, 531 deletions
diff --git a/OSX/README.txt b/OSX/README.txt index 3f27a04..47b0bf4 100644 --- a/OSX/README.txt +++ b/OSX/README.txt @@ -1,533 +1,545 @@ -Heimdall (c) 2010-2011 Benjamin Dobell, Glass Echidna
-http://www.glassechidna.com.au/products/heimdall/
-
-DISCLAIMER:
-
- This software attempts to flash your Galaxy S device. The very nature of
- flashing is dangerous. As with all flashing software, Heimdall has the
- potential to damage (brick) your device if not used carefully. If you're
- concerned, don't use this software. Flashing ROMs onto your phone may also
- void your warranty. Benjamin Dobell and Glass Echidna are not responsible
- for the result of your actions.
-
-
-These instructions are for OS X operating systems.
-
-
-Installing Heimdall and Heimdall Frontend Binaries:
-
- 1. Run "Heimdall Suite.pkg" and follow the instructions.
-
- 2. Reboot your system.
-
- 3. Done
-
-
-
-Flashing Heimdall Firmware Package with Heimdall Frontend:
-
- As of Heimdall Frontend 1.3 there are now two main ways to flash a ROM from
- Heimdall Frontend. The simpler and preferred option is to download a
- Heimdall Firmware Package and follow the following steps.
-
-
- 1. Fully charge your device (use the wall charger as it's faster).
-
- 2. Open the Heimdall Frontend (heimdall-frontend) application.
-
- 3. From the "Load Package" tab, under the "Heimdall Firmware Package"
- section click the "Browse" button.
-
- 4. Use the dialogue that appears to navigate to, and select, the Heimdall
- firmware package that you wish to flash.
-
- 5. You will see progress bars appear as the package is decompressed and
- extracted.
-
- When the package has finished being decompressed you should see
- information about the particular firmware package that has been
- selected.
-
- 6. Verify that your device is listed under "Supported Devices". If it's not
- then STOP immediately! DO NOT flash this firmware to your device!
- Instead search for an appropriate firmware package for your device.
-
- If you believe there is a mistake and your device is actually
- supported please get in contact with the firmware developer (not Glass
- Echidna!) and ask them to rectify the issue. If the developer provided
- a URL you may be able to contact them by pressing the "Homepage" button.
-
- 7. If you've verified your device is supported you may continue to press
- the "Load / Customise" button.
-
- 8. You should now be looking at the "Flash" tab. If not verify that you did
- in fact push the "Load / Customise" button.
-
- Generally, you won't NEED or WANT to customise a firmware package! In
- which case you can safely move on to step 9.
-
- Nonetheless, the "Flash" tab provides you with a means to customise the
- firmware package before flashing it to your device. See "Performing a
- Custom Flash with Heimdall Frontend" for more details.
-
- 9. Put your Galaxy S device into download mode and plug it in to your PC.
-
- Download mode can be accessed several different ways depending on your
- particular device model. If you're unsure how to do this please search
- online for the appropriate method.
-
- 10. Press the "Start" button.
-
- 11. Heimdall Frontend will display the progress and inform you when the
- flash is complete.
-
- If something went wrong i.e. your device wasn't detected because it
- wasn't in download mode, then the status section will let you know the
- cause of the problem.
-
-
-
-Performing a Custom Flash with Heimdall Frontend:
-
- This is the advanced means of flashing firmware to your device.
-
- If you're not an advanced user or a developer, in the event that a Heimdall
- Firmware Package doesn't exist for the particular firmware (or files) that
- you wish to flash, then I strongly recommend you get in touch with developer
- of the firmware (or files) and politely ask them to create a Heimdall
- Firmware Package for you. In doing so then you don't have to worry about
- making mistakes due to inexperience.
-
- If you're looking to customise an existing Heimdall Firmware Package then
- follow steps 1-8 of "Flashing Heimdall Firmware Package with Heimdall
- Frontend" then start from below with step 5.
-
-
- 1. Fully charge your device (use the wall charger as it's faster).
-
- 2. Download a decrypted Samsung Galaxy S ROM or a Heimdall Firmware Package
- and extract everything to the one directory.
-
- 3. If the ROM is not a Heimdall Firmware Package it may instead be provided
- as multiple archives (nested or otherwise), extract them all to the same
- location.
-
- NOTE: If you want to use the CSC then extract it last.
-
- 3. Open the Heimdall Frontend (heimdall-frontend) application.
-
- 4. Select the "Flash" tab. From the "Flash" tab you're able to completely
- customise a flash.
-
- 5. Before you can chose which partitions you want to flash with particular
- files you MUST first select a PIT file. To do this click the "Browse"
- button in the "PIT" section. This will open a dialogue allowing you to
- navigate to and select a valid PIT (.pit) file.
-
- If you do not already have a valid PIT file stored on your computer you
- can download your device's PIT file from the "Utilities" tab.
-
- 6. If a valid PIT file has been selected then "Add" button below the
- "Partitions (Files)" list-box will become enabled. Press this button to
- add a partition to your flash.
-
- 7. When you first add a partition you will see the "Partition Name" and
- "Partition ID" be populated with information. Use the "Partition Name"
- drop down to select which partition you wish to flash. "Partition ID"
- will automatically update and is never directly editable.
-
- 8. You must then select a file to flash to the partition that you just
- specified using the "Browse" button under the "File / Partition". You
- will not be able to flash, create a firmware package or add another
- partition until you have selected a file. However, you're still able to
- press the "Remove" button if you've decided not to flash the partition
- you've just specified.
-
- 9. When you've specified a file name then you'll be able to see the updated
- information in the partition list to the right. You can select any
- partition from this list and customise it as you see fit.
-
- You can also remove a partition from the list by selecting it and
- clicking the "Remove" button. Removing a partition from the list doesn't
- remove it from your device, it simply means it will not be flashed.
-
- 10. Repeat steps 7-9 as often as needed to specify all the partions/files
- that you wish to flash.
-
- 11. Now you can chose whether you would like to repartition your device as
- well as whether you would like to prevent the device rebooting once a
- flash has been completed. These options can be enabled or disabled by
- toggling the "Repartition" and "No Reboot" check-boxes.
-
- In the general case you will only need to enable repartition if you wish
- to change the PIT file on your device. Keep in mind that repartitioning
- will wipe your device!
-
- The "No Reboot" option is rarely required. It's mostly in place so you
- can manually boot straight into recovery mode after a flash (rather than
- booting up normally).
-
- 12. If you've added at least one partition to your flash (and selected a
- file for that partition) then the "Start" button will be enabled. Press
- the "Start" button to begin the flashing process.
-
- You may notice that the "Create Package" tab becomes available at the
- whenever the "Start" button becomes available. From this tab you're able
- to create a reusable, redistributable Heimdall Firmware Package with the
- files and partitions you just selected. See "How to Create a Heimdall
- Firmware Package" for details.
-
- 13. Heimdall Frontend will display the progress and inform you when the
- flash is complete.
-
- If something went wrong i.e. your device wasn't detected because it
- wasn't in download mode, then the status section will let you know the
- cause of the problem.
-
-
-
-Flashing Firmware from Command Line:
-
- 1. Fully charge your phone (use the wall charger as it's faster).
-
- 2. Download a decrypted Samsung Galaxy S ROM or a Heimdall Firmware Package
- and extract everything to the one directory.
-
- 3. If the ROM is not a Heimdall Firmware Package it may instead be provided
- as multiple archives (nested or otherwise), extract them all to the same
- location.
-
- NOTE: If you want to use the CSC then extract it last. If you're asked
- to overwrite files then do so.
-
- 4. Put your Galaxy S device into download mode and plug it in..
-
- 5. Open a terminal and navigate to the directory where you extracted
- the ROM/firmware files.
-
- 6. Type the following to list all the functionality Heimdall supports:
-
- heimdall help
-
- 7. Use the instructions to manually enter a command with all the files you
- want to flash.
-
- Here is an example that does a full flash and repartition on a GT-I9000:
-
- heimdall flash --repartition --pit s1_odin_20100512.pit --factoryfs factoryfs.rfs --cache cache.rfs --dbdata dbdata.rfs --primary-boot boot.bin --secondary-boot Sbl.bin --param param.lfs --kernel zImage --modem modem.bin
-
-
- 8. Heimdall will display the progress as it flashes so that you know things
- are working as they should.
-
-
-
-How to Create a Heimdall Firmware Package:
-
- Firstly, Heimdall's firmware package format is just a regular TAR archive
- compressed with gzip. The only two real requirements are that a valid
- firmware.xml must be included (refer to Appendix A) and you can only
- include files (no directories, links etc.) As such if you'd like there is
- nothing preventing you from creating Heimdall packages manually. Of course
- Heimdall Frontend provides a simple user interface that takes care of all
- the hard work for you.
-
- There are two ways in which you can create a firmware package. You can
- create a package from scratch, or you can load an existing package, apply
- modifications and then save the package. Creating a package from scratch
- is the preferred approach, by taking this approach you're far less likely
- to run into file name length limitations. These are not Heimdall's own
- limitation but rather a limitation of the TAR archive format.
-
- Before you can access Heimdall Frontend's firmware creation functionality
- (available from the "Create Package" tab) you must first specify which
- files will be included in your package, as well as a few flashing options
- i.e. Whether or not users should repartition when flashing. This
- information must be filled out from the "Flash" tab in exactly the same
- fashion you would provide information to flash your device (see "Performing
- a Custom Flash with Heimdall Frontend"). As mentioned above, it's not the
- preferred means, but you're able to load an existing package as a starting
- point for this information.
-
- Once you've specified the files/partitions you wish to include in your
- firmware package the "Create Package" tab will become available. Clicking
- this tab will display additional information that you can include in your
- package. In order to continue you must fill out all sections except for the
- URLs section, which is optional. The following is a break-down of what all
- these options mean.
-
- - General Firmware Information: -
-
- Firmware Name - This is the name of your particular firmware. An
- example would be "Cyanogenmod".
-
- Firmware Version - This is the version identifier for your package. Any
- valid string will be accepted although a the inclusion of decimal
- point version number is preferred i.e. "7.1". If it makes sense
- then feel free to append a text string like "RC1" or "Beta 1" to
- the decimal point version.
-
- Platform Name - This is the name of the platform (or operating system)
- that your firmware is based on. In most cases this will simply be
- "Android".
-
- Platform Version - This is the operating system version that your
- firmware is based on. Again decimal point version numbers are
- preferred over text, i.e. "2.3.4" is preferred over "Gingerbread".
-
-
- - Developers -
-
- URLs (Optional):
-
- Homepage - Here you can enter your personal URL or a URL particularly
- pertaining to the firmware being packaged. The URL must be well
- formed for it to work. An example of a well formed URL is
- "http://www.glassechidna.com.au/products/heimdall/". It is
- important to include "http://" in order to specify the protocol as
- other protocols such as "ftp://" are equally valid although
- unlikely to be used.
-
- Donate - Here you can enter a URL that will link users to a page to
- make donations for the effort you've put into developing your
- firmware. Once again the URL must be well formed but there is no
- requirement on how your donation page should work. For instance
- both "http://www.glassechidna.com.au/donate/" and
- "http://forum.xda-developers.com/donatetome.php?u=2710388" are
- equally valid.
-
- Developer Info:
-
- Name - Here you can enter in the name of individual team members or a
- team name. Click "Add" and the developer will be added to the list
- on the right. If you make a mistake you can select a developer from
- the list and click "Remove". You can list as many developers as you
- like however visual constraints of the "Load Package" tab means
- only a few names will be visible. Where possible you may want to
- opt for team names over listing individual team members.
-
-
- - Supported Devices -
-
- This section allows you to create a list of devices that are supported by
- your particular firmware. Although Heimdall isn't capable of enforcing this
- we strongly recommend you take this section seriously. If filled out
- correctly you could help save a number of accidental bricks!
-
- Device Info:
-
- Manufacturer - This is where you can enter the name of the manufacturer
- for a particular device. For now this will most likely be
- "Samsung".
-
- Name - This is the human readable name for a particular device.
- "Galaxy S", "Galaxy S II", "Droid Charge", "Vibrant" and
- "Galaxy S (Telstra)" are all valid names. There are a lot of
- possible variations here so be as specific as you think is
- necessary.
-
- Product Code - This is by far the most important bit of device
- information. Device names tend to be region specific and further
- subject to the whims of telecommunication companies and resellers.
- Product Codes (or product IDs) are designated by manufacturers and
- are generally the definitive means of referring to a particular
- device. Examples are "GT-I9000", "GT-I9100" and "SCH-I897". If
- you're unsure of a particular product code then both Google and
- GSMArena are your friends!
-
-
- After filling out all the necessary information the "Build" button will be
- enabled. If it's still disabled then you know you're missing some required
- information. In particular you must specify at least one developer and at
- least one supported device. Pressing the "Build" button will bring up a
- save dialogue where you must chose a file name for your particular package.
- Don't worry about specifying the ".tar.gz" extension Heimdall Frontend will
- take care of this automatically.
-
- Once you've chosen a file name Heimdall Frontend will begin the process of
- building the firmware package. In doing so a valid firmware.xml file will
- be generated from the information entered. All files will be archived in a
- single TAR file then the TAR archive will be compressed via gzip
- compression. Compression will take a little while but you will see progress
- bars so you know the application hasn't hung. When the progress bars
- disappear you're finished making your package.
-
- Congratulations! You're now ready to redistribute your firmware package
- online or by any means you see fit.
-
-
-
-Appendix A - firmware.xml
-
-The following details a part of the Heimdall Firmware Package format. This
-is only relevant to developers or advanced users who wish to create Heimdall
-Firmware Packages outside of Heimdall Frontend or in some way integrate support
-for the format in their own software.
-
-
-All Heimdall Firmware Packages must contain a file called firmware.xml. This
-file stores flash information and meta-data for the package as well as
-information about other files contained within the package.
-
-The format is fairly straight-forward so it won't be explained in great detail.
-Nonetheless the following is an example of a valid firmware.xml file.
-
-<?xml version="1.0" encoding="UTF-8"?>
-<firmware version="1">
- <name>Test Firmware</name>
- <version>1.1</version>
- <platform>
- <name>Android</name>
- <version>2.3.4</version>
- </platform>
- <developers>
- <name>Benjamin Dobell</name>
- <name>Hedonism Bot</name>
- </developers>
- <url>http://www.glassechidna.com.au/</url>
- <donateurl>http://www.glassechidna.com.au/donate/</donateurl>
- <devices>
- <device>
- <manufacturer>Samsung</manufacturer>
- <product>GT-I9000</product>
- <name>Galaxy S</name>
- </device>
- <device>
- <manufacturer>Samsung</manufacturer>
- <product>GT-I9000T</product>
- <name>Galaxy S (Telstra)</name>
- </device>
- <device>
- <manufacturer>Samsung</manufacturer>
- <product>GT-I9000M</product>
- <name>Vibrant</name>
- </device>
- </devices>
- <pit>Nl3276-I9000 s1_odin_20100512.pit</pit>
- <repartition>0</repartition>
- <noreboot>0</noreboot>
- <files>
- <file>
- <id>0</id>
- <filename>gq3276-boot.bin</filename>
- </file>
- <file>
- <id>24</id>
- <filename>Uh3276-cache.rfs</filename>
- </file>
- <file>
- <id>22</id>
- <filename>em3276-factoryfs.rfs</filename>
- </file>
- <file>
- <id>11</id>
- <filename>fl3276-modem.bin</filename>
- </file>
- <file>
- <id>21</id>
- <filename>Xd3276-param.lfs</filename>
- </file>
- <file>
- <id>3</id>
- <filename>if3276-Sbl.bin</filename>
- </file>
- <file>
- <id>6</id>
- <filename>cr3276-zImage</filename>
- </file>
- </files>
-</firmware>
-
-
-New lines need not be included and the order in which elements are specified
-does not need to match that of the above example.
-
-One and only one <firmware> element must be included. The <firmware> element
-must also have a version attribute specified. The version must be parsable as
-an integer and indicates what version of the Heimdall Firmware Package
-specification the package adheres to.
-
-All data is stored as strings, however a <file>'s <id> element must be parsable
-as an integer. The <id> value represents the partition ID (according to the
-specified PIT file) that the file should be flashed to.
-
-A <firmware>'s <repartition> and <noreboot> elements must also be parsable as
-an integer. However, as they represent boolean values, a value of zero ("0")
-means false (or disabled) where as a non-zero value (typically "1") means true
-(or enabled).
-
-File names are specified relative to the TAR archive in which firmware.xml and
-all other files are to be stored. Heimdall Firmware Packages do not support
-directories or links, as such file names should only be a name and not a path.
-
-<url> and <donateurl> are the only optional elements, all other elements must
-be included.
-
-
-
-Appendix B - Installing Heimdall from Source:
-
- 1. First make sure you have installed XCode and pkgconfig.
-
- NOTE: There are several different ways you can install pkgconfig, one
- option is to use Macports (http://www.macports.org/).
-
- 2. Open a terminal and navigate to the directory you downloaded,
- or extracted, Heimdall to.
-
- 3. Download, compile and install libusb-1.0:
-
+Heimdall (c) 2010-2013 Benjamin Dobell, Glass Echidna +http://www.glassechidna.com.au/products/heimdall/ + +DISCLAIMER: + + This software attempts to flash your Galaxy S device. The very nature of + flashing is dangerous. As with all flashing software, Heimdall has the + potential to damage (brick) your device if not used carefully. If you're + concerned, don't use this software. Flashing ROMs onto your phone may also + void your warranty. Benjamin Dobell and Glass Echidna are not responsible + for the result of your actions. + + +These instructions are for OS X operating systems. + + +Installing Heimdall and Heimdall Frontend Binaries: + + 1. Run "Heimdall Suite.pkg" and follow the instructions. + + 2. Reboot your system. + + 3. Done + + + +Flashing Heimdall Firmware Package with Heimdall Frontend: + + As of Heimdall Frontend 1.3 there are now two main ways to flash a ROM from + Heimdall Frontend. The simpler and preferred option is to download a + Heimdall Firmware Package and follow the following steps. + + + 1. Fully charge your device (use the wall charger as it's faster). + + 2. Open the Heimdall Frontend (heimdall-frontend) application. + + 3. From the "Load Package" tab, under the "Heimdall Firmware Package" + section click the "Browse" button. + + 4. Use the dialogue that appears to navigate to, and select, the Heimdall + firmware package that you wish to flash. + + 5. You will see progress bars appear as the package is decompressed and + extracted. + + When the package has finished being decompressed you should see + information about the particular firmware package that has been + selected. + + 6. Verify that your device is listed under "Supported Devices". If it's not + then STOP immediately! DO NOT flash this firmware to your device! + Instead search for an appropriate firmware package for your device. + + If you believe there is a mistake and your device is actually + supported please get in contact with the firmware developer (not Glass + Echidna!) and ask them to rectify the issue. If the developer provided + a URL you may be able to contact them by pressing the "Homepage" button. + + 7. If you've verified your device is supported you may continue to press + the "Load / Customise" button. + + 8. You should now be looking at the "Flash" tab. If not verify that you did + in fact push the "Load / Customise" button. + + Generally, you won't NEED or WANT to customise a firmware package! In + which case you can safely move on to step 9. + + Nonetheless, the "Flash" tab provides you with a means to customise the + firmware package before flashing it to your device. See "Performing a + Custom Flash with Heimdall Frontend" for more details. + + 9. Put your Galaxy S device into download mode and plug it in to your PC. + + Download mode can be accessed several different ways depending on your + particular device model. If you're unsure how to do this please search + online for the appropriate method. + + 10. Press the "Start" button. + + 11. Heimdall Frontend will display the progress and inform you when the + flash is complete. + + If something went wrong i.e. your device wasn't detected because it + wasn't in download mode, then the status section will let you know the + cause of the problem. + + + +Performing a Custom Flash with Heimdall Frontend: + + This is the advanced means of flashing firmware to your device. + + If you're not an advanced user or a developer, in the event that a Heimdall + Firmware Package doesn't exist for the particular firmware (or files) that + you wish to flash, then I strongly recommend you get in touch with developer + of the firmware (or files) and politely ask them to create a Heimdall + Firmware Package for you. In doing so then you don't have to worry about + making mistakes due to inexperience. + + If you're looking to customise an existing Heimdall Firmware Package then + follow steps 1-8 of "Flashing Heimdall Firmware Package with Heimdall + Frontend" then start from below with step 5. + + + 1. Fully charge your device (use the wall charger as it's faster). + + 2. Download a decrypted device ROM or a Heimdall Firmware Package + and extract everything to the one directory. + + 3. If the ROM is not a Heimdall Firmware Package it may instead be provided + as multiple archives (nested or otherwise), extract them all to the same + location. + + NOTE: If you want to use the CSC then extract it last. + + 3. Open the Heimdall Frontend (heimdall-frontend) application. + + 4. Select the "Flash" tab. From the "Flash" tab you're able to completely + customise a flash. + + 5. Before you can chose which partitions you want to flash with particular + files you MUST first select a PIT file. To do this click the "Browse" + button in the "PIT" section. This will open a dialogue allowing you to + navigate to and select a valid PIT (.pit) file. + + If you do not already have a valid PIT file stored on your computer you + can download your device's PIT file from the "Utilities" tab. + + 6. If a valid PIT file has been selected then "Add" button below the + "Partitions (Files)" list-box will become enabled. Press this button to + add a partition to your flash. + + 7. When you first add a partition you will see the "Partition Name" and + "Partition ID" be populated with information. Use the "Partition Name" + drop down to select which partition you wish to flash. "Partition ID" + will automatically update and is never directly editable. + + 8. You must then select a file to flash to the partition that you just + specified using the "Browse" button under the "File / Partition". You + will not be able to flash, create a firmware package or add another + partition until you have selected a file. However, you're still able to + press the "Remove" button if you've decided not to flash the partition + you've just specified. + + 9. When you've specified a file name then you'll be able to see the updated + information in the partition list to the right. You can select any + partition from this list and customise it as you see fit. + + You can also remove a partition from the list by selecting it and + clicking the "Remove" button. Removing a partition from the list doesn't + remove it from your device, it simply means it will not be flashed. + + 10. Repeat steps 7-9 as often as needed to specify all the partions/files + that you wish to flash. + + 11. Now you can chose whether you would like to repartition your device as + well as whether you would like to prevent the device rebooting once a + flash has been completed. These options can be enabled or disabled by + toggling the "Repartition" and "No Reboot" check-boxes. + + In the general case you will only need to enable repartition if you wish + to change the PIT file on your device. Keep in mind that repartitioning + will wipe your device! + + The "No Reboot" option is rarely required. It's mostly in place so you + can manually boot straight into recovery mode after a flash (rather than + booting up normally). + + 12. If you've added at least one partition to your flash (and selected a + file for that partition) then the "Start" button will be enabled. Press + the "Start" button to begin the flashing process. + + You may notice that the "Create Package" tab becomes available at the + whenever the "Start" button becomes available. From this tab you're able + to create a reusable, redistributable Heimdall Firmware Package with the + files and partitions you just selected. See "How to Create a Heimdall + Firmware Package" for details. + + 13. Heimdall Frontend will display the progress and inform you when the + flash is complete. + + If something went wrong i.e. your device wasn't detected because it + wasn't in download mode, then the status section will let you know the + cause of the problem. + + + +Flashing Firmware from Command Line: + + 1. Fully charge your phone (use the wall charger as it's faster). + + 2. Download a decrypted device ROM or a Heimdall Firmware Package + and extract everything to the one directory. + + 3. If the ROM is not a Heimdall Firmware Package it may instead be provided + as multiple archives (nested or otherwise), extract them all to the same + location. + + NOTE: If you want to use the CSC then extract it last. If you're asked + to overwrite files then do so. + + 4. Put your Galaxy S device into download mode and plug it in.. + + 5. Open a terminal and navigate to the directory where you extracted + the ROM/firmware files. + + 6. Type the following to list all the functionality Heimdall supports: + + heimdall help + + 7. Before flashing, you must first know the names of the partitions you + wish to flash. These can be obtained by executing: + + heimdall print-pit --no-reboot + + The inclusion of --no-reboot ensures the phone will not reboot after PIT + file has been downloaded and displayed. After executing a command with + the --no-reboot argument, the next command should include the --resume + argument. + + NOTE: You can still safely reboot your phone manually (with the power + button) after executing --no-reboot commands. + + 8. Use the help and print-pit output to construct a command with all the + file you want to flash. + + Here is an example that does a full flash and repartition on a GT-I9000: + + heimdall flash --repartition --resume --pit s1_odin_20100512.pit --FACTORYFS factoryfs.rfs --CACHE cache.rfs --DBDATA dbdata.rfs --IBL+PBL boot.bin --SBL Sbl.bin --PARAM param.lfs --KERNEL zImage --MODEM modem.bin + + 9. Heimdall will display the progress as it flashes so that you know things + are working as they should. + + + +How to Create a Heimdall Firmware Package: + + Firstly, Heimdall's firmware package format is just a regular TAR archive + compressed with gzip. The only two real requirements are that a valid + firmware.xml must be included (refer to Appendix A) and you can only + include files (no directories, links etc.) As such if you'd like there is + nothing preventing you from creating Heimdall packages manually. Of course + Heimdall Frontend provides a simple user interface that takes care of all + the hard work for you. + + There are two ways in which you can create a firmware package. You can + create a package from scratch, or you can load an existing package, apply + modifications and then save the package. Creating a package from scratch + is the preferred approach, by taking this approach you're far less likely + to run into file name length limitations. These are not Heimdall's own + limitation but rather a limitation of the TAR archive format. + + Before you can access Heimdall Frontend's firmware creation functionality + (available from the "Create Package" tab) you must first specify which + files will be included in your package, as well as a few flashing options + i.e. Whether or not users should repartition when flashing. This + information must be filled out from the "Flash" tab in exactly the same + fashion you would provide information to flash your device (see "Performing + a Custom Flash with Heimdall Frontend"). As mentioned above, it's not the + preferred means, but you're able to load an existing package as a starting + point for this information. + + Once you've specified the files/partitions you wish to include in your + firmware package the "Create Package" tab will become available. Clicking + this tab will display additional information that you can include in your + package. In order to continue you must fill out all sections except for the + URLs section, which is optional. The following is a break-down of what all + these options mean. + + - General Firmware Information: - + + Firmware Name - This is the name of your particular firmware. An + example would be "Cyanogenmod". + + Firmware Version - This is the version identifier for your package. Any + valid string will be accepted although a the inclusion of decimal + point version number is preferred i.e. "7.1". If it makes sense + then feel free to append a text string like "RC1" or "Beta 1" to + the decimal point version. + + Platform Name - This is the name of the platform (or operating system) + that your firmware is based on. In most cases this will simply be + "Android". + + Platform Version - This is the operating system version that your + firmware is based on. Again decimal point version numbers are + preferred over text, i.e. "2.3.4" is preferred over "Gingerbread". + + + - Developers - + + URLs (Optional): + + Homepage - Here you can enter your personal URL or a URL particularly + pertaining to the firmware being packaged. The URL must be well + formed for it to work. An example of a well formed URL is + "http://www.glassechidna.com.au/products/heimdall/". It is + important to include "http://" in order to specify the protocol as + other protocols such as "ftp://" are equally valid although + unlikely to be used. + + Donate - Here you can enter a URL that will link users to a page to + make donations for the effort you've put into developing your + firmware. Once again the URL must be well formed but there is no + requirement on how your donation page should work. For instance + both "http://www.glassechidna.com.au/donate/" and + "http://forum.xda-developers.com/donatetome.php?u=2710388" are + equally valid. + + Developer Info: + + Name - Here you can enter in the name of individual team members or a + team name. Click "Add" and the developer will be added to the list + on the right. If you make a mistake you can select a developer from + the list and click "Remove". You can list as many developers as you + like however visual constraints of the "Load Package" tab means + only a few names will be visible. Where possible you may want to + opt for team names over listing individual team members. + + + - Supported Devices - + + This section allows you to create a list of devices that are supported by + your particular firmware. Although Heimdall isn't capable of enforcing this + we strongly recommend you take this section seriously. If filled out + correctly you could help save a number of accidental bricks! + + Device Info: + + Manufacturer - This is where you can enter the name of the manufacturer + for a particular device. For now this will most likely be + "Samsung". + + Name - This is the human readable name for a particular device. + "Galaxy S", "Galaxy S II", "Droid Charge", "Vibrant" and + "Galaxy S (Telstra)" are all valid names. There are a lot of + possible variations here so be as specific as you think is + necessary. + + Product Code - This is by far the most important bit of device + information. Device names tend to be region specific and further + subject to the whims of telecommunication companies and resellers. + Product Codes (or product IDs) are designated by manufacturers and + are generally the definitive means of referring to a particular + device. Examples are "GT-I9000", "GT-I9100" and "SCH-I897". If + you're unsure of a particular product code then both Google and + GSMArena are your friends! + + + After filling out all the necessary information the "Build" button will be + enabled. If it's still disabled then you know you're missing some required + information. In particular you must specify at least one developer and at + least one supported device. Pressing the "Build" button will bring up a + save dialogue where you must chose a file name for your particular package. + Don't worry about specifying the ".tar.gz" extension Heimdall Frontend will + take care of this automatically. + + Once you've chosen a file name Heimdall Frontend will begin the process of + building the firmware package. In doing so a valid firmware.xml file will + be generated from the information entered. All files will be archived in a + single TAR file then the TAR archive will be compressed via gzip + compression. Compression will take a little while but you will see progress + bars so you know the application hasn't hung. When the progress bars + disappear you're finished making your package. + + Congratulations! You're now ready to redistribute your firmware package + online or by any means you see fit. + + + +Appendix A - firmware.xml + +The following details a part of the Heimdall Firmware Package format. This +is only relevant to developers or advanced users who wish to create Heimdall +Firmware Packages outside of Heimdall Frontend or in some way integrate support +for the format in their own software. + + +All Heimdall Firmware Packages must contain a file called firmware.xml. This +file stores flash information and meta-data for the package as well as +information about other files contained within the package. + +The format is fairly straight-forward so it won't be explained in great detail. +Nonetheless the following is an example of a valid firmware.xml file. + +<?xml version="1.0" encoding="UTF-8"?> +<firmware version="1"> + <name>Test Firmware</name> + <version>1.1</version> + <platform> + <name>Android</name> + <version>2.3.4</version> + </platform> + <developers> + <name>Benjamin Dobell</name> + <name>Hedonism Bot</name> + </developers> + <url>http://www.glassechidna.com.au/</url> + <donateurl>http://www.glassechidna.com.au/donate/</donateurl> + <devices> + <device> + <manufacturer>Samsung</manufacturer> + <product>GT-I9000</product> + <name>Galaxy S</name> + </device> + <device> + <manufacturer>Samsung</manufacturer> + <product>GT-I9000T</product> + <name>Galaxy S (Telstra)</name> + </device> + <device> + <manufacturer>Samsung</manufacturer> + <product>GT-I9000M</product> + <name>Vibrant</name> + </device> + </devices> + <pit>Nl3276-I9000 s1_odin_20100512.pit</pit> + <repartition>0</repartition> + <noreboot>0</noreboot> + <files> + <file> + <id>0</id> + <filename>gq3276-boot.bin</filename> + </file> + <file> + <id>24</id> + <filename>Uh3276-cache.rfs</filename> + </file> + <file> + <id>22</id> + <filename>em3276-factoryfs.rfs</filename> + </file> + <file> + <id>11</id> + <filename>fl3276-modem.bin</filename> + </file> + <file> + <id>21</id> + <filename>Xd3276-param.lfs</filename> + </file> + <file> + <id>3</id> + <filename>if3276-Sbl.bin</filename> + </file> + <file> + <id>6</id> + <filename>cr3276-zImage</filename> + </file> + </files> +</firmware> + + +New lines need not be included and the order in which elements are specified +does not need to match that of the above example. + +One and only one <firmware> element must be included. The <firmware> element +must also have a version attribute specified. The version must be parsable as +an integer and indicates what version of the Heimdall Firmware Package +specification the package adheres to. + +All data is stored as strings, however a <file>'s <id> element must be parsable +as an integer. The <id> value represents the partition ID (according to the +specified PIT file) that the file should be flashed to. + +A <firmware>'s <repartition> and <noreboot> elements must also be parsable as +an integer. However, as they represent boolean values, a value of zero ("0") +means false (or disabled) where as a non-zero value (typically "1") means true +(or enabled). + +File names are specified relative to the TAR archive in which firmware.xml and +all other files are to be stored. Heimdall Firmware Packages do not support +directories or links, as such file names should only be a name and not a path. + +<url> and <donateurl> are the only optional elements, all other elements must +be included. + + + +Appendix B - Installing Heimdall from Source: + + 1. First make sure you have installed XCode and pkgconfig. + + NOTE: There are several different ways you can install pkgconfig, one + option is to use Macports (http://www.macports.org/). + + 2. Open a terminal and navigate to the directory you downloaded, + or extracted, Heimdall to. + + 3. Download, compile and install libusb-1.0: + http://www.libusb.org/ - NOTE: Alternatively you may install Macport's libusb-devel package.
-
- 4. Enter the following commands to compile libpit.
-
- cd libpit
- ./configure
- make
- cd ..
-
- NOTE: There is no need to run "sudo make install".
-
- 4. Enter the following commands to compile and install Heimdall:
-
- cd heimdall
- ./configure
- make
- sudo make install
- cd ..
-
- 5. If you haven't installed the driver before, enter the following:
-
- cd OSX
- sudo ./install-kext.sh
-
- 6. Done
-
-
-
-Appendix C - Installing Heimdall Frontend from Source:
-
- 1. Compile and install Heimdall, see Appendix B.
-
- 2. First make sure you have installed XCode from your OS X install DVD.
- You'll also need Qt 4.7 or later, available from:
-
- http://qt.nokia.com/downloads/
-
- 3. Open a terminal and navigate to the directory you extracted Heimdall to.
-
- 4. Enter the following commands to compile and install Heimdall Frontend:
-
- cd heimdall-frontend
- qmake heimdall-frontend.pro
-
- 5. Open Finder and navigate to the heimdall-frontend sub-directory. Open
- the newly created XCode project.
-
- 6. From the menu bar select Build -> Build. This outputs heimdall-frontend
- to /Applications
-
- 7. Done
-
+ NOTE: Alternatively you may install Macport's libusb-devel package. + + 4. Enter the following commands to compile libpit. + + cd libpit + ./configure + make + cd .. + + NOTE: There is no need to run "sudo make install". + + 4. Enter the following commands to compile and install Heimdall: + + cd heimdall + ./configure + make + sudo make install + cd .. + + 5. If you haven't installed the driver before, enter the following: + + cd OSX + sudo ./install-kext.sh + + 6. Done + + + +Appendix C - Installing Heimdall Frontend from Source: + + 1. Compile and install Heimdall, see Appendix B. + + 2. First make sure you have installed XCode from your OS X install DVD. + You'll also need Qt 4.7 or later, available from: + + http://qt.nokia.com/downloads/ + + 3. Open a terminal and navigate to the directory you extracted Heimdall to. + + 4. Enter the following commands to compile and install Heimdall Frontend: + + cd heimdall-frontend + qmake heimdall-frontend.pro + + 5. Open Finder and navigate to the heimdall-frontend sub-directory. Open + the newly created XCode project. + + 6. From the menu bar select Build -> Build. This outputs heimdall-frontend + to /Applications + + 7. Done + |