From ff7e38b32faf3c5ca628b1fb35c07d30cc86e5cf Mon Sep 17 00:00:00 2001 From: "Wolfgang (Wolle) Ewald" Date: Wed, 6 Jan 2021 15:40:25 +0100 Subject: Update Alert_Window_Mode.ino --- examples/Alert_Window_Mode/Alert_Window_Mode.ino | 25 ++++++++++++------------ 1 file changed, 13 insertions(+), 12 deletions(-) (limited to 'examples/Alert_Window_Mode') diff --git a/examples/Alert_Window_Mode/Alert_Window_Mode.ino b/examples/Alert_Window_Mode/Alert_Window_Mode.ino index a68b684..0a099ad 100644 --- a/examples/Alert_Window_Mode/Alert_Window_Mode.ino +++ b/examples/Alert_Window_Mode/Alert_Window_Mode.ino @@ -6,7 +6,8 @@ * mode. You can change the mode with the function setAlertModeAndLimit_V * * Further information can be found on: -* https://wolles-elektronikkiste.de/ads1115 +* https://wolles-elektronikkiste.de/ads1115 (German) +* https://wolles-elektronikkiste.de/en/ads1115-a-d-converter-with-amplifier (English) * ***************************************************************************/ @@ -57,7 +58,7 @@ void setup() { */ adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change range - /* Set number of conversions out of limit after which the alert pin will be active + /* Set number of conversions out of limit after which alert pin asserts * - or you can disable the alert (including conversion ready alert) * * ADS1115_ASSERT_AFTER_1 -> after 1 conversion @@ -88,10 +89,10 @@ void setup() { */ adc.setMeasureMode(ADS1115_CONTINUOUS); //comment or change you want to change to single shot - /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will - * be active when measured values are beyond the maximum limit or outside the window + /* Choose maximum limit or maximum and minimum alert limit (window) in volts - alert pin will + * assert when measured values are beyond the maximum limit or outside the window * Upper limit first: setAlertLimit_V(MODE, maximum, minimum) - * In max limit mode the minimum value is the limit where the alert pin will be deactivated + * In max limit mode the minimum value is the limit where the alert pin assertion is cleared * again (if not latched!) * * ADS1115_MAX_LIMIT @@ -100,9 +101,9 @@ void setup() { */ adc.setAlertModeAndLimit_V(ADS1115_WINDOW, 3.0, 1.5); //you can change modes / limits - /* Enable or disable latch. If latch is enabled the alarm pin will be active until the - * conversion register is read (getResult functions). If disabled the alarm pin will be - * deactivated with next value within limits. + /* Enable or disable latch. If latch is enabled the alert pin will assert until the + * conversion register is read (getResult functions). If disabled the alert pin assertion + * will be cleared with next value within limits. * * ADS1115_LATCH_DISABLED (default) * ADS1115_LATCH_ENABLED @@ -111,16 +112,16 @@ void setup() { /* Sets the alert pin polarity if active: * - * Enable or disable latch. If latch is enabled the alarm pin will be active until the - * conversion register is read (getResult functions). If disabled the alarm pin will be - * deactivated with next value within limits. + * Enable or disable latch. If latch is enabled the alert pin will assert until the + * conversion register is read (getResult functions). If disabled the alert pin assertion + * will be cleared with next value within limits. * * ADS1115_ACT_LOW -> active low (default) * ADS1115_ACT_HIGH -> active high */ //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default - /* With this function the alert pin will be active, when a conversion is ready. + /* With this function the alert pin will assert, when a conversion is ready. * In order to deactivate, use the setAlertLimit_V function */ //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default -- cgit v1.2.3