+traffic Service CLI menu +ces CES CLI menu (empty) +pon PON CLI menu +debug PON debug command rptwanstat config report wan status to MEC tcont add/delete/flush a Tcont flow configure the parameters of a flow queue configure the parameters of a Tcont Queue sendomci Send a OMCI message prbs Enable/disable transmitting PRBS continuously dyingGsend Enable/disable transmitting PRBS continuously omcidbg Enable/disable kernel OMCI log reportGemCnt Enable/disable report gem counter to MEC throughput Enable/disable throughput test ponmode Enable/disable qos dump_classifier Dump classifier rule gem_to_cpu trap gem port all packets to cpu +hw PON Hardware level command show Show hardware status or configurations read_reg Read register value write_reg Write register value +ca PON cortina command show Show cortina status or configurations +app PON APP command show Show database in PMR app sendmsg Send Msg to PMR app ber_interval Configure the BER interval sf_threshold The threshold of BIP to report signal failure sd_threshold The threshold of BIP to report signal degrade sn Set the serial number of the ONT password Set the password of ONT to1_to2 Set the To1 To2 timer of ONT show show PON information +eth ETH CLI menu +debug Ethernet Debug System CLI menu pack Ethernet CLI debug function for pack driver brdg Ethernet CLI debug function for SOC bridge phy Ethernet CLI debug function for PHY showconn Show ethernet connection debug info ethdbg enable/disable the eth debug flag show Ethernet CLI Show +voip VoIP CLI menu (empty) +omci omci CLI menu +debug OMCI Debug System CLI menu showemrcfg show the configuration of EMR from MEC crc enable the crc check of omci message omiterr Enable/disable omitting OMCI errors acpower Start or stop power shedding allocid Function call mec_AddAllocId ponstate Function call mec_HandlePonStateChange +voip OMCI VoIP System CLI menu show show the configuration of VMR from MEC +defaultxml MEC Xml List CLI menu show show the List of default Xml from MEC crc_commit runtime xml add crc restore_xml runtime xml restore show Show the information of MEC clear Clear the runtime data +router router CLI menu (empty) +dmr DMR CLI menu (empty) +hpna HPNA CLI menu (empty) +system System CLI menu +mib MIB CLI menu +debug MIB Debug System CLI menu dump Dump current mib to a file reset Reset mib to default values show Show the content of mib tables +log LOG CLI menu +kernel KERNEL LOG CLI menu (empty) show Print out a log dump dump the content of a log file set Save a log to a file clear Clear a log collectlog Collectlog all log +env ENV CLI menu show Print out enviroment variables +misc MISC CLI menu +bob BOSA CLI menu eep Misc CLI Show unlock Misc CLI Show echo Misc CLI Show 2090 Misc CLI Show preheat Misc CLI Show auto Misc CLI Show automod Misc CLI Show restart Misc CLI Show +debug Misc Debug System CLI menu showwc Show write counter of mtd device showbad Show bad blocks of mtd device show Misc CLI Show rf Misc CLI Show filter Misc CLI Show agc Misc CLI Show ponalarm Misc CLI Show mpcode Read or write eeprom : EEP_MFG_PRODUCTCODE mpsn Read or write eeprom : EEP_MFG_PRODUCTSERIAL mhwv Read or write eeprom : EEP_MFG_HWVERSION lasersn Read or write eeprom : EEP_MFG_LASERSERIAL mac1 Read or write eeprom : EEP_MFG_MAC1 mac2 Read or write eeprom : EEP_MFG_MAC2 eepver Read or write eeprom : EEP_MFG_EEPVER burnin Read or write burnin flag : EEP_MFG_BURNIN rfthigh Read or write rfthigh in unit of 64 ohm : EEP_MFG_RFT_HIGH rftlow Read or write rftlow in unit of 64 ohm: EEP_MFG_RFT_LOW rithigh Read or write rithigh in unit of 64 ohm : EEP_MFG_RIT_HIGH ritlow Read or write ritlow in unit of 64 ohm: EEP_MFG_RIT_LOW major Read or write eeprom : EEP_HW_FUNCTIONMAJOR minor Read or write eeprom : EEP_HW_FUNCTIONMINOR hwver Read or write eeprom : EEP_HW_VERSION vendor Read or write eeprom : EEP_EQ_VENDORID eqsn Read or write eeprom : EEP_EQ_SERIALNUMBER eqsnvend Read or write eeprom : EEP_EQ_SNVENDOR eqvid Read or write eeprom : EEP_EQ_VERSIONID eqid Read or write eeprom : EEP_EQ_ID img_name Read or write eeprom : EEP_SW_BOOTIMAGE admin_ip Read or write eeprom : EEP_SW_IPADDR admin_mask Read or write eeprom : EEP_SW_IPMASK server_ip Read or write eeprom : EEP_SW_HOSTIPADDR admin_gw Read or write eeprom : EEP_SW_GATEIPADDR ftp_user Read or write eeprom : EEP_SW_FTPUSER ftp_passwd Read or write eeprom : EEP_SW_FTPPASS bootflag Read or write eeprom : EEP_SW_BOOTFLAG admin_en Read or write eeprom : EEP_SW_BOOTREMOTEEN xgspon_regid Read or write eeprom : XGS PON Registration ID test_en Read or write eeprom : EEP_SW_BOOTTESTEN notcomplete Read or write eeprom : EEP_SW_BOOTNOTCOMPLETE act_img Read or write eeprom : EEP_SW_ACTIVEIMAGE commit_img Read or write eeprom : EEP_SW_COMMITIMAGE pon_passwd Read or write eeprom : EEP_APP_GPONPASSWORD register_id Read or write eeprom : EEP_APP_GPONPASSWORD hwerr Read or write eeprom : EEP_HW_DIAGNOSTICCODE vdsl2_vendor Read or write eeprom : EEP_VDSL2_VENDORID ssh_en Read or write eeprom : EEPROM_RW_CMD i2c_r This command read i2c device in raw mode i2c_w This command write i2c device in raw mode write_mem This command is used to write otp read_mem This command is used to read otp sendevent This command is used to send led event directly testloaden This command enable test load for manufacture testensn This command enable test load for manufacture eep_reset This command restore EEPROM factory default configuration eep_r8 This command read EEPROM in raw mode eep_w8 This command write EEPROM in raw mode eep_crc This command update/check EEPROM crc value exeep_r8 This command read EEPROM in raw mode exeep_w8 This command write EEPROM in raw mode exeep_crc This command update/check EEPROM crc value eepinfo This command show eep info. clearcfg This command is used to clear ONT runtime config , if full para is set, clear loid also!Usage: clearcfg [full] final_check This command is used to show some important information for checking! led This command is used to only turn on green leds,red leds or off all leds!Usage: led gon/ron/off testloaden This command enable test load for manufacture testensn This command enable test load for manufacture get_gpio_val This command get gpio value diswdt This command disable for manufacture bosa This command is used to set bosa version and type image_copy This command copy one image to another at next boot time stopreboot Stop reboot command for debug +manu Manufacture CLI menu we This command write eeprom for manufacture wep This command only write PC for manufacture wes This command only write SN for manufacture wem1 This command only write MAC1 for manufacture wem2 This command only write MAC2 for manufacture ledon This command turn on all led ledoff This command turn off all led final_check This command do final check get_gpio_val This command get gpio value trans This command show transceiver info temp This command show system temperature er This command enable rf dr This command diable rf ef This command enable filter df This command disable filter ten This command enable test load wd This command disable watchdog tensn This command enable test load, special for BL olt ces_main This command configure ces connection for main test board ces_back This command configure ces connection for backup test board check_boot_status This command check boot status check_ranging_statusThis command check ranging status check_usb_port This command does manu test for USB device reset_button_test This command is used for Reset Button test factory_reset Clear all configuration and return to factory setting load_certfile Load ACS HTTPS private Cert file into ONT +fs File System CLI menu show Show the content of system memory supgrade super user Upgrade Image from Local Ftp Server flash System Flash memory Operation command upgrade Upgrade Image from Local Ftp Server check check the content of system mtd +net NET CLI menu mirror Set mirror debug dump Set dump frames debug log Open/Close driver debug log atconn Active connection debug show Show NetMgr Data +shell Shell +debug System Debug CLI menu showtimer Show timers showtask Show task state starttimer Start timers stoptimer Start timers md5 calculate MD5 value from input string md5num calculate MD5 number string from input string printlog Set the log level to print to console ontver Show ONT Software Version custom Get/Set ONT Software custom information