1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
|
---
title: Root Procedure for Huawei MA5671A
has_children: false
parent: Huawei MA5671A
layout: default
---
1. Take the SFP molex and the 4 coloured cables and solder them to the molex according to the following diagram:
| USB TTL(UART) Adapter | wire colour in picture | SFP 20pins Molex connector |
| --------------------- | ---------------------- | -------------------------- |
| 3.3V | red | pin #15 and #16 |
| TX | orange | pin #2 |
| RX | yellow | pin #7 |
| GND | green | pin #14 |
{% include alert.html content="Use GND wire as ON/OFF switch, otherwise there will be a slight delay before data is displayed on the console (putty/TeraTerm)." alert="Important" icon="svg-warning" color="yellow" %}
{% include alert.html content="Try PIN 10 or other GND PINs if it doesn't work with 14." alert="Note" icon="svg-warning" color="yellow" %}
{% include alert.html content="Some USB TTL adapters label TX and RX pins the other way around: try to swap them if it doesn't work." alert="Note" icon="svg-warning" color="yellow" %}
{:style="counter-reset:none"}
1. Install python and `pyserial` with `pip`
```shell
pip install pyserial
```
1. Make the connections as shown to a TTL adapter except for GND (which remains detached and is used as a switch)
{% include image.html file="ma5671a-root-1.jpg" alt="Example of how the sfp-ttl connection should look like" caption="Example of how the sfp-ttl connection should look like" %}
{% include image.html file="new-root-procedure\board-molex-arduino.jpg" alt="Example of how the sfp-ttl connection should look like with a custom board" caption="Example of how the sfp-ttl connection should look like with a custom board" %}
{% include image.html file="ma5671a-root-2.jpg" alt="Molex SFP" caption="Molex SFP" %}
{:style="counter-reset:none"}
1. Open Tera Term (or other serial terminal emulator), find the correct serial port of the TTL adapter, change the port on the script on line 7 instead of `COM8`.
1. After this, run the following python script and connect the GND pin:
```py
import sys
import time
import serial.tools
try:
ser = serial.Serial("COM8", 115200, parity=serial.PARITY_NONE, stopbits=serial.STOPBITS_ONE, bytesize=serial.EIGHTBITS)
print('[+] Use serial port device:', ser.name)
print('[+] Waiting for trigger characters...')
while True:
try:
recv = ser.readline().decode()
except Exception as x:
print("Decode errore", x)
continue
if recv.startswith('U-Boot'):
print('[+] Received! transfer enable command...')
print('[+] Transfer command sequence 1')
t_end = time.time() + 3
while time.time() < t_end:
ser.write(chr(3).encode())
time.sleep(1)
print('[+] Transfer command sequence 2')
ser.write('setenv bootdelay 3\n'.encode())
time.sleep(1)
print('[+] Transfer command sequence 3')
ser.write('setenv asc0 0\n'.encode())
time.sleep(1)
print('[+] Transfer command sequence 4')
ser.write(
'setenv preboot "gpio input 105;gpio input 106;gpio input 107;gpio input 108;gpio set 3;gpio set 109;gpio set 110;gpio clear 423;gpio clear 422;gpio clear 325;gpio clear 402;gpio clear 424"\n'.encode())
time.sleep(1)
print('[+] Transfer command sequence 5')
ser.write('saveenv\n'.encode())
time.sleep(3)
print('[+] Transfer command sequence 6')
ser.write('reset\n'.encode())
print('[+] Enable command transfer complete! rebooting...')
break
else:
print(recv)
except Exception as e:
try:
print('[!] Error:', e)
sys.exit(1)
finally:
e = None
del e
except (KeyboardInterrupt, SystemExit):
ser.close()
sys.exit(1)
```
{:style="counter-reset:none"}
1. Reboot the stick
1. Open Tera Term (or other serial terminal emulator), after load press `enter` to activate the console
{% include image.html file="new-root-procedure\press-enter.jpg" alt="Press enter for activate the console" caption="Press enter for activate the console" %}
{:style="counter-reset:none"}
1. With `sed` change the default shell from `/opt/lantiq/bin/minishell` to `/bin/ash` the file `/etc/passwd`:
```shell
sed -i "s|/opt/lantiq/bin/minishell|/bin/ash|g" /etc/passwd
```
{% include alert.html content="Do not use `vim`!" alert="Important" icon="svg-warning" color="red" %}
{% include alert.html content="Take attention to kernel panics, they happen often! Be quick, if a kernel panic happens wait for the reboot and try again." alert="Important" icon="svg-warning" color="yellow" %}
```shell
[ 34.612000] Kernel panic - not syncing: Fatal exception in interrupt
[ 34.612000] Rebooting in 3 seconds..
```
{% include alert.html content="The cause of these kernel panics could be insufficient power supply." alert="Info" icon="svg-info" color="blue" %}
{:style="counter-reset:none"}
1. Reboot it this time connected to the router with cage or mediaconverter, with the port set to an IP on the 192.168.1.0/24 subnet (the stick has the IP 192.168.1.10)
{% include alert.html content="If your subnet is 192.168.1.0/24 make sure you have no ip conflicts." alert="Note" icon="svg-warning" color="yellow" %}
{% include alert.html content="Be sure to disable SFP TX fault detection otherwise the RX loss will prevent you from connecting to the mini SFP ONT at this point. Don't simply attach the fiber optic to work it around or you OLT may ban you." alert="Note" icon="svg-warning" color="yellow" %}
{:style="counter-reset:none"}
1. Run the terminal and login to the stick with ssh
```shell
ssh root@192.168.1.10
```
The password is `admin123`.
{% include alert.html content="If you use a modern OpenSSH version (e.g. >= 8.8) you will have to enable some deprecated algorithms: ssh -oKexAlgorithms=+diffie-hellman-group1-sha1 -oHostKeyAlgorithms=+ssh-dss [...]" alert="Info" icon="svg-info" color="blue" %}
# Miscellaneous Links
- [Come avere i 2.5 Gbps su un unico dispositivo senza il Fastgate](https://forum.fibra.click/d/17836-come-avere-i-25-gbps-su-un-unico-dispositivo-senza-il-fastgate)
- [Support MA5671A SFP GPON](https://forum.openwrt.org/t/support-ma5671a-sfp-gpon/48042)
- [La fibre Orange à 2Gbps, sur un routeur MikroTik 10Gbps CCR2004, via un ONT SFP+](https://lafibre.info/remplacer-livebox/guide-de-connexion-fibre-directement-sur-un-routeur-voire-meme-en-2gbps/msg832904/#msg832904)
- [Bypassing the HH3K up to 2.5Gbps using a BCM57810S NIC](https://www.dslreports.com/forum/r32230041-Internet-Bypassing-the-HH3K-up-to-2-5Gbps-using-a-BCM57810S-NIC)
- [Bypassing the HH3K up to 2.5Gbps using a BCM57810S NIC](https://www.dslreports.com/forum/r32230041-Internet-Bypassing-the-HH3K-up-to-2-5Gbps-using-a-BCM57810S-NIC)
|
