1 files changed, 129 insertions, 0 deletions

diff --git a/examples/Continuous/Continuous.ino b/examples/Continuous/Continuous.ino
new file mode 100644
index 0000000..3c8313a
--- /dev/null
+++ b/examples/Continuous/Continuous.ino
@@ -0,0 +1,129 @@
+/***************************************************************************
+* Example sketch for the ADS1115_WE library
+*
+* This sketch shows how to use the ADS1115 in continuous mode. 
+*  
+* Further information can be found on:
+* https://wolles-elektronikkiste.de/ads1115
+* 
+***************************************************************************/
+
+#include<ADS1115_WE.h> 
+#include<Wire.h>
+#define I2C_ADDRESS 0x48
+
+ADS1115_WE adc(I2C_ADDRESS);
+// ADS1115_WE adc = ADS1115_WE(); // Alternative: uses default address 0x48
+
+void setup() {
+  Wire.begin();
+  Serial.begin(9600);
+  if(!adc.init()){
+    Serial.println("ADS1115 not connected!");
+  }
+
+  /* Set the voltage range of the ADC to adjust the gain
+   * Please note that you must not apply more than VDD + 0.3V to the input pins!
+   * 
+   * ADS1115_RANGE_6144  ->  +/- 6144 mV
+   * ADS1115_RANGE_4096  ->  +/- 4096 mV
+   * ADS1115_RANGE_2048  ->  +/- 2048 mV (default)
+   * ADS1115_RANGE_1024  ->  +/- 1024 mV
+   * ADS1115_RANGE_0512  ->  +/- 512 mV
+   * ADS1115_RANGE_0256  ->  +/- 256 mV
+   */
+  adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change parameter to change range
+
+  /* Set the inputs to be compared
+   *  
+   *  ADS1115_COMP_0_1    ->  compares 0 with 1 (default)
+   *  ADS1115_COMP_0_3    ->  compares 0 with 3
+   *  ADS1115_COMP_1_3    ->  compares 1 with 3
+   *  ADS1115_COMP_2_3    ->  compares 2 with 3
+   *  ADS1115_COMP_0_GND  ->  compares 0 with GND
+   *  ADS1115_COMP_1_GND  ->  compares 1 with GND
+   *  ADS1115_COMP_2_GND  ->  compares 2 with GND
+   *  ADS1115_COMP_3_GND  ->  compares 3 with GND
+   */
+  adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change channel
+
+  /* Set number of conversions after which the alert pin will be active
+   * - or you can disable the alert 
+   *  
+   *  ADS1115_ASSERT_AFTER_1  -> after 1 conversion
+   *  ADS1115_ASSERT_AFTER_2  -> after 2 conversions
+   *  ADS1115_ASSERT_AFTER_4  -> after 4 conversions
+   *  ADS1115_DISABLE_ALERT   -> disable comparator / alert pin (default) 
+   */
+  //adc.setAlertPinMode(ADS1115_ASSERT_AFTER_1); //uncomment if you want to change the default
+
+  /* Set the conversion rate in SPS (samples per second)
+   * Options should be self-explaining: 
+   * 
+   *  ADS1115_8_SPS 
+   *  ADS1115_16_SPS  
+   *  ADS1115_32_SPS 
+   *  ADS1115_64_SPS  
+   *  ADS1115_128_SPS (default)
+   *  ADS1115_250_SPS 
+   *  ADS1115_475_SPS 
+   *  ADS1115_860_SPS 
+   */
+  // adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default
+
+  /* Set continuous or single shot mode:
+   * 
+   *  ADS1115_CONTINUOUS  ->  continuous mode
+   *  ADS1115_SINGLE     ->  single shot mode (default)
+   */
+  adc.setMeasureMode(ADS1115_CONTINUOUS); //comment line/change parameter to change mode
+
+   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 
+   *  be active when measured values are beyond the maximum limit or outside the window 
+   *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)
+   *  In max limit mode the minimum value is the limit where the alert pin will be deactivated (if 
+   *  not latched)  
+   * 
+   *  ADS1115_MAX_LIMIT
+   *  ADS1115_WINDOW
+   * 
+   */
+  //adc.setAlertModeAndLimit_V(ADS1115_MAX_LIMIT, 3.0, 1.5); //uncomment if you want to change the default
+  
+  /* Enable or disable latch. If latch is enabled the alarm pin will be active until the
+   * conversion register is read (getResult functions). If disabled the alarm pin will be
+   * deactivated with next value within limits. 
+   *  
+   *  ADS1115_LATCH_DISABLED (default)
+   *  ADS1115_LATCH_ENABLED
+   */
+  //adc.setAlertLatch(ADS1115_LATCH_ENABLED); //uncomment if you want to change the default
+
+  /* Sets the alert pin polarity if active:
+   *  
+   * Enable or disable latch. If latch is enabled the alarm pin will be active until the
+   * conversion register is read (getResult functions). If disabled the alarm pin will be
+   * deactivated with next value within limits. 
+   *  
+   * ADS1115_ACT_LOW  ->  active low (default)   
+   * ADS1115_ACT_HIGH ->  active high
+   */
+  //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default
+ 
+  /* With this function the alert pin will be active, when a conversion is ready.
+   * In order to deactivate, use the setAlertLimit_V function  
+   */
+  //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default
+
+  Serial.println("ADS1115 Example Sketch - Continuous Mode");
+  Serial.println();
+}
+
+void loop() {
+  float voltage = 0.0;
+  voltage = adc.getResult_V(); // alternative: getResult_mV for Millivolt
+  Serial.print("Channel 0 vs GND [V]: ");
+  Serial.println(voltage);
+  Serial.println("-------------------------------");
+  delay(2000);
+}