From 912c53d44d555527f120ff6cb6e2dbe73748791e Mon Sep 17 00:00:00 2001 From: "Wolfgang (Wolle) Ewald" Date: Wed, 6 Jan 2021 16:07:51 +0100 Subject: Update Single_Shot_Conv_Ready_Controlled.ino --- .../Single_Shot_Conv_Ready_Controlled.ino | 25 +++++++++++----------- 1 file changed, 13 insertions(+), 12 deletions(-) (limited to 'examples/Single_Shot_Conv_Ready_Controlled') diff --git a/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino b/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino index 9ca409e..f1c2696 100644 --- a/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino +++ b/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino @@ -5,7 +5,8 @@ * This does not work in the continuous mode. * * Further information can be found on: -* https://wolles-elektronikkiste.de/ads1115 +* https://wolles-elektronikkiste.de/ads1115 (German) +* https://wolles-elektronikkiste.de/en/ads1115-a-d-converter-with-amplifier (English) * ***************************************************************************/ @@ -48,7 +49,7 @@ void setup() { */ adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change channels - /* Set number of conversions after which the alert pin will be active + /* Set number of conversions after which the alert pin will assert * - or you can disable the alert * * ADS1115_ASSERT_AFTER_1 -> after 1 conversion @@ -79,10 +80,10 @@ void setup() { */ //adc.setMeasureMode(ADS1115_CONTINUOUS); //continuous mode does not work with conversion ready (isBusy) - /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will - * be active when measured values are beyond the maximum limit or outside the window + /* Choose maximum limit or maximum and minimum alert limit (window) in volts - alert pin will + * assert when measured values are beyond the maximum limit or outside the window * Upper limit first: setAlertLimit_V(MODE, maximum, minimum) - * In max limit mode the minimum value is the limit where the alert pin will be deactivated (if + * In max limit mode the minimum value is the limit where the alert pin assertion will be cleared (if * not latched) * * ADS1115_MAX_LIMIT @@ -91,9 +92,9 @@ void setup() { */ //adc.setAlertModeAndLimit_V(ADS1115_MAX_LIMIT, 3.0, 1.5); //uncomment if you want to change the default - /* Enable or disable latch. If latch is enabled the alarm pin will be active until the - * conversion register is read (getResult functions). If disabled the alarm pin will be - * deactivated with next value within limits. + /* Enable or disable latch. If latch is enabled the alert pin will assert until the + * conversion register is read (getResult functions). If disabled the alert pin assertion will be + * cleared with next value within limits. * * ADS1115_LATCH_DISABLED (default) * ADS1115_LATCH_ENABLED @@ -102,16 +103,16 @@ void setup() { /* Sets the alert pin polarity if active: * - * Enable or disable latch. If latch is enabled the alarm pin will be active until the - * conversion register is read (getResult functions). If disabled the alarm pin will be - * deactivated with next value within limits. + * Enable or disable latch. If latch is enabled the alert pin will assert until the + * conversion register is read (getResult functions). If disabled the alarm pin assertion + * will be cleared with next value within limits. * * ADS1115_ACT_LOW -> active low (default) * ADS1115_ACT_HIGH -> active high */ //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default - /* With this function the alert pin will be active, when a conversion is ready. + /* With this function the alert pin will assert, when a conversion is ready. * In order to deactivate, use the setAlertLimit_V function */ //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default -- cgit v1.2.3