blob: af2e4b3d307128fe9cc0892cf9ec8953812abe0f (
plain) (
tree)
|
|
//
// Values are 32 bit values layed out as follows:
//
// 3 3 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1
// 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
// +---+-+-+-----------------------+-------------------------------+
// |Sev|C|R| Facility | Code |
// +---+-+-+-----------------------+-------------------------------+
//
// where
//
// Sev - is the severity code
//
// 00 - Success
// 01 - Informational
// 10 - Warning
// 11 - Error
//
// C - is the Customer code flag
//
// R - is a reserved bit
//
// Facility - is the facility code
//
// Code - is the facility's status code
//
//
// Define the facility codes
//
//
// Define the severity codes
//
//
// MessageId: NDIS_ERROR_CODE_OUT_OF_RESOURCE
//
// MessageText:
//
// Adapter %2 : Insufficient memory or system resources was available
// for the netcard driver to initialize. (The last DWORD of the data section
// below contains a detailed error code.)
//
#define NDIS_ERROR_CODE_OUT_OF_RESOURCE ((NDIS_ERROR_CODE)0xC0001389L)
//
// MessageId: NDIS_ERROR_CODE_HARDWARE_FAILURE
//
// MessageText:
//
// Adapter %2 : The adapter hardware failed to initialize. Please
// check that the adapter card is properly inserted into its slot and that the
// network cable is connected. If its is an ISA adapter check that the interrupt
// number, DMA channel and IO location in the adapter configuration match the
// settings on the adapter card. (The data section below includes a driver
// specific error code of 0x07 and the last two DWORDS give a detailed error
// code.)
//
#define NDIS_ERROR_CODE_HARDWARE_FAILURE ((NDIS_ERROR_CODE)0xC000138AL)
//
// MessageId: NDIS_ERROR_CODE_ADAPTER_NOT_FOUND
//
// MessageText:
//
// Adapter %2 : The netcard driver could not allocate sufficient memory
// for transmit and recive buffers. The number of RX and TX slots and
// the maximum frame size may have been reduced to reduce the amount
// of memory required.
//
#define NDIS_ERROR_CODE_ADAPTER_NOT_FOUND ((NDIS_ERROR_CODE)0xC000138BL)
//
// MessageId: NDIS_ERROR_CODE_INTERRUPT_CONNECT
//
// MessageText:
//
// Adapter %2 : The netcard driver was not able to connect the
// adapter card's interrupt. Please ensure that the adapter card is properly
// inserted into its slot. If it is an ISA adapter then check that the
// interrupt number specified in the adapter configuration matches that
// set on the adapter card.
//
#define NDIS_ERROR_CODE_INTERRUPT_CONNECT ((NDIS_ERROR_CODE)0xC000138CL)
//
// MessageId: NDIS_ERROR_CODE_DRIVER_FAILURE
//
// MessageText:
//
// Adapter %2 : One of the paramters in the registry entry for this adapter
// is invalid. If possible a default value will have been used.
//
#define NDIS_ERROR_CODE_DRIVER_FAILURE ((NDIS_ERROR_CODE)0xC000138DL)
//
// MessageId: NDIS_ERROR_CODE_UNSUPPORTED_CONFIGURATION
//
// MessageText:
//
// Adapter %2 : The maximum frame size setting in the registry is too
// large. The driver has trimmed it down to the maximum allowable setting. (The
// data section below includes a driver specific error code of 0xC, followed by
// the actual maximum frame size used in the last DWORD. Replace the value in the
// registry with this).
//
#define NDIS_ERROR_CODE_UNSUPPORTED_CONFIGURATION ((NDIS_ERROR_CODE)0xC0001391L)
//
// MessageId: NDIS_ERROR_CODE_INAVLID_VALUE_FROM_ADAPTER
//
// MessageText:
//
// Adapter %2 : The adapter could not be opened onto the ring. Please ensure
// that the network cable is connected to the adapter and that the token
// ring is fully connected. Also ensure that all the nodes on your ring
// are set to the same speed and that all nodes have different addresses.
//
#define NDIS_ERROR_CODE_INAVLID_VALUE_FROM_ADAPTER ((NDIS_ERROR_CODE)0xC0001392L)
//
// MessageId: NDIS_ERROR_CODE_MISSING_CONFIGURATION_PARAMETER
//
// MessageText:
//
// Adapter %2 : An essential registry parameter is missing for this adapter.
// For MCA and EISA adapters the registry must contain BusType and SlotNumber
// parameters. For ISA adapters the registry must contain IoLocation,
// InterruptNumber and DmaChannel parameters.
//
#define NDIS_ERROR_CODE_MISSING_CONFIGURATION_PARAMETER ((NDIS_ERROR_CODE)0xC0001393L)
//
// MessageId: NDIS_ERROR_CODE_INVALID_DOWNLOAD_FILE_ERROR
//
// MessageText:
//
// Adapter %2 : Either the file MDGMPORT.BIN is not present in the device drivers
// directory, the file is of the wrong version or the file is corrupt.
//
#define NDIS_ERROR_CODE_INVALID_DOWNLOAD_FILE_ERROR ((NDIS_ERROR_CODE)0xC000139CL)
//
// MessageId: NDIS_ERROR_CODE_MEMORY_CONFLICT
//
// MessageText:
//
// Adapter %2 : Either MMIO memory was not assigned or could not be mapped into
// virtual memory. PIO transfer method is being used instead of MMIO.
//
#define NDIS_ERROR_CODE_MEMORY_CONFLICT ((NDIS_ERROR_CODE)0x80001399L)
|
