#ident "@(#) NEC mode542x.h 1.3 94/11/04 15:39:44"
/*++
Copyright (c) 1992 Microsoft Corporation
Module Name:
Mode542x.h
Abstract:
This module contains all the global data used by the Cirrus Logic
CL-542x driver.
Environment:
Kernel mode
Revision History:
--*/
//
// The next set of tables are for the CL542x
// Note: all resolutions supported
//
//
// 640x480 16-color mode (BIOS mode 12) set command string for CL 542x.
//
USHORT CL542x_640x480[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
3,
0x0009, 0x000a, 0x000b, // no banking in 640x480 mode
EOD
};
//
// 800x600 16-color (60Hz refresh) mode set command string for CL 542x.
//
USHORT CL542x_800x600[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
3,
0x0009, 0x000a, 0x000b, // no banking in 800x600 mode
EOD
};
//
// 1024x768 16-color (60Hz refresh) mode set command string for CL 542x.
//
USHORT CL542x_1024x768[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
3,
#if ONE_64K_BANK
0x0009, 0x000a, 0x000b,
#endif
#if TWO_32K_BANKS
0x0009, 0x000a, 0x010b,
#endif
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
EOD
};
//-----------------------------
// standard VGA text modes here
// 80x25 at 640x350
//
//-----------------------------
//
// 80x25 text mode set command string for CL 542x.
// (720x400 pixel resolution; 9x16 character cell.)
//
USHORT CL542x_80x25Text[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
3,
0x0009, 0x000a, 0x000b, // no banking in text mode
EOD
};
//
// 80x25 text mode set command string for CL 542x.
// (640x350 pixel resolution; 8x14 character cell.)
//
USHORT CL542x_80x25_14_Text[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
3,
0x0009, 0x000a, 0x000b, // no banking in text mode
EOD
};
//
// 1280x1024 16-color mode (BIOS mode 0x6C) set command string for CL 542x.
//
USHORT CL542x_1280x1024[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
3,
#if ONE_64K_BANK
0x0009, 0x000a, 0x000b,
#endif
#if TWO_32K_BANKS
0x0009, 0x000a, 0x010b,
#endif
EOD
};
//
// 640x480 64k-color mode (BIOS mode 0x64) set command string for CL 542x.
//
USHORT CL542x_640x480_64k[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
4,
0x0506, // Some BIOS's set Chain Odd maps bit
#if ONE_64K_BANK
0x0009, 0x000a, 0x000b,
#endif
#if TWO_32K_BANKS
0x0009, 0x000a, 0x010b,
#endif
EOD
};
#ifdef _X86_
//
// 640x480 256-color mode (BIOS mode 0x5F) set command string for CL 542x.
//
USHORT CL542x_640x480_256[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
3,
#if ONE_64K_BANK
0x0009, 0x000a, 0x000b,
#endif
#if TWO_32K_BANKS
0x0009, 0x000a, 0x010b,
#endif
EOD
};
//
// 800x600 256-color mode (BIOS mode 0x5C) set command string for CL 542x.
//
USHORT CL542x_800x600_256[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM,
GRAPH_ADDRESS_PORT,
3,
#if ONE_64K_BANK
0x0009, 0x000a, 0x000b,
#endif
#if TWO_32K_BANKS
0x0009, 0x000a, 0x010b,
#endif
EOD
};
#else
//
// NOTE(DBCS) : Update 94/09/12 - NEC Corporation
//
// - Add mode set command string for NEC MIPS machine.
//
// - 640x480 256 color 72Hz
// - 800x600 256 color 56 / 60Hz
// - 1024x768 256 color 70 / 45Hz
//
#if defined(DBCS) && defined(_MIPS_)
//
// For MIPS NEC machine only
//
//
// 640x480 256-color 60Hz mode (BIOS mode 0x5F) set command string for
// CL 542x.
//
USHORT CL542x_640x480_256_60[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM, // begin setmode
SEQ_ADDRESS_PORT,
15, // count
0x100, // start sync reset
0x0101,0x0F02,0x0003,0x0E04, // program up sequencer
//
// the Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed Liner addressing.
//
(LA_MASK << 12 | 0x0107),
0x0008,
0x4A0B,0x5B0C,0x450D,0x7E0E,
0x2B1B,0x2F1C,0x301D,0x331E,
OB, // point sequencer index to ff
SEQ_ADDRESS_PORT,
0x0F,
METAOUT+MASKOUT, // masked out.
SEQ_DATA_PORT,
0xDF,0x20, // and mask, xor mask
OB, // misc. register
MISC_OUTPUT_REG_WRITE_PORT,
0xE3,
OW, // text/graphics bit
GRAPH_ADDRESS_PORT,
0x506,
OW, // end sync reset
SEQ_ADDRESS_PORT,
0x300,
OW, // unprotect crtc 0-7
CRTC_ADDRESS_PORT_COLOR,
0x2011,
METAOUT+INDXOUT, // program crtc registers
CRTC_ADDRESS_PORT_COLOR,
28,0, // count, startindex
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0x5D, 0x4F, 0x50, 0x82, 0x53, 0x9F,
0x00, 0x3E, 0x00, 0x40, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0xE1, 0x83,
0xDF, 0x50, 0x00, 0xE7, 0x04, 0xE3,
0xFF, 0x00, 0x00, 0x22,
#else
0x5f, 0x4f, 0x50, 0x82, 0x54, 0x80,
0x0b, 0x3e, 0x00, 0x40, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0xea, 0x8c,
0xdf, 0x50, 0x00, 0xe7, 0x04, 0xe3,
0xff, 0x00, 0x00, 0x22,
#endif // defined(DBCS) && defined(_MIPS_)
METAOUT+INDXOUT, // program gdc registers
GRAPH_ADDRESS_PORT,
9,0, // count, startindex
0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
0x05, 0x0F, 0xFF,
IB, // prepare atc for writing
INPUT_STATUS_1_COLOR,
METAOUT+ATCOUT, // program atc registers
ATT_ADDRESS_PORT,
21,0, // count, startindex
0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B,
0x0C, 0x0D, 0x0E, 0x0F, 0x41, 0x00,
0x0F, 0x00, 0x00,
OB, // turn video on.
ATT_ADDRESS_PORT,
0x20,
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
OWM,
GRAPH_ADDRESS_PORT,
3,
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed it for Liner addressing.
//
0x0009, 0x000a, 0x000b,
EOD
};
//
// 640x480 256-color 72Hz mode (BIOS mode 0x5F) set command string for
// CL 542x.
//
USHORT CL542x_640x480_256_72[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM, // begin setmode
SEQ_ADDRESS_PORT,
15, // count
0x100, // start sync reset
0x0101,0x0F02,0x0003,0x0E04, // program up sequencer
//
// the Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed Liner addressing.
//
(LA_MASK << 12 | 0x0107),
0x0008,
0x4A0B,0x5B0C,0x450D,0x420E,
0x2B1B,0x2F1C,0x301D,0x1F1E,
OB, // point sequencer index to ff
SEQ_ADDRESS_PORT,
0x0F,
METAOUT+MASKOUT, // masked out.
SEQ_DATA_PORT,
0xDF,0x20, // and mask, xor mask
OB, // misc. register
MISC_OUTPUT_REG_WRITE_PORT,
0xEF,
OW, // text/graphics bit
GRAPH_ADDRESS_PORT,
0x506,
OW, // end sync reset
SEQ_ADDRESS_PORT,
0x300,
OW, // unprotect crtc 0-7
CRTC_ADDRESS_PORT_COLOR,
0x2011,
METAOUT+INDXOUT, // program crtc registers
CRTC_ADDRESS_PORT_COLOR,
28,0, // count, startindex
//
// NOTE(DBCS) : Update 95/06/30 - NEC Corporation (same as cirrus\mode542x.h)
//
// - Set Mode Type is VESA compatible. (Old Miss match)
//
#if defined(DBCS) && defined(_MIPS_)
0x61, 0x4F, 0x50, 0x82, 0x54, 0x99,
0xF6, 0x1F, 0x00, 0x40, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0xE0, 0x03,
0xDF, 0x50, 0x00, 0xE7, 0x04, 0xE3,
0xFF, 0x00, 0x00, 0x22,
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
// 0x63, 0x4F, 0x50, 0x82, 0x55, 0x9A, thase parameter not match
// 0x06, 0x3E, 0x00, 0x40, 0x00, 0x00, VESA Mode.
// 0x00, 0x00, 0x00, 0x00, 0xE8, 0x8B,
// 0xDF, 0x50, 0x00, 0xE7, 0x04, 0xE3,
// 0xFF, 0x00, 0x00, 0x22,
#else
0x5f, 0x4f, 0x50, 0x82, 0x54, 0x80,
0x0b, 0x3e, 0x00, 0x40, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0xea, 0x8c,
0xdf, 0x50, 0x00, 0xe7, 0x04, 0xe3,
0xff, 0x00, 0x00, 0x22,
#endif // defined(DBCS) && defined(_MIPS_)
METAOUT+INDXOUT, // program gdc registers
GRAPH_ADDRESS_PORT,
9,0, // count, startindex
0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
0x05, 0x0F, 0xFF,
IB, // prepare atc for writing
INPUT_STATUS_1_COLOR,
METAOUT+ATCOUT, // program atc registers
ATT_ADDRESS_PORT,
21,0, // count, startindex
0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B,
0x0C, 0x0D, 0x0E, 0x0F, 0x41, 0x00,
0x0F, 0x00, 0x00,
OB, // turn video on.
ATT_ADDRESS_PORT,
0x20,
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
OWM,
GRAPH_ADDRESS_PORT,
3,
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed it for Liner addressing.
//
0x0009, 0x000a, 0x000b,
EOD
};
//
// 800x600 256-color 56Hz mode (BIOS mode 0x5C) set command string for
// CL 542x.
//
USHORT CL542x_800x600_256_56[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM, // begin setmode
SEQ_ADDRESS_PORT,
15, // count
0x100, // start sync reset
0x0101,0x0F02,0x0003,0x0E04, // program up sequencer
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed Liner addressing.
//
(LA_MASK << 12 | 0x0107),
0x0008,
0x4A0B,0x5B0C,0x450D,0x7E0E,
0x2B1B,0x2F1C,0x301D,0x331E,
OB, // point sequencer index to ff
SEQ_ADDRESS_PORT,
0x0F,
METAOUT+MASKOUT, // masked out.
SEQ_DATA_PORT,
0xDF,0x20, // and mask, xor mask
OB, // misc. register
MISC_OUTPUT_REG_WRITE_PORT,
0xEF,
OW, // text/graphics bit
GRAPH_ADDRESS_PORT,
0x506,
OW, // end sync reset
SEQ_ADDRESS_PORT,
0x300,
OW, // unprotect crtc 0-7
CRTC_ADDRESS_PORT_COLOR,
0x2011,
METAOUT+INDXOUT, // program crtc registers
CRTC_ADDRESS_PORT_COLOR,
28,0, // count, startindex
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0x7B, 0x63, 0x64, 0x80, 0x69, 0x12,
0x6F, 0xF0, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x58, 0x8A,
0x57, 0x64, 0x00, 0x5F, 0x91, 0xE3,
0xFF, 0x00, 0x00, 0x22,
#else
0x7D, 0x63, 0x64, 0x80, 0x6D, 0x1C,
0x98, 0xF0, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x7B, 0x80,
0x57, 0x64, 0x00, 0x5F, 0x91, 0xe3,
0xff, 0x00, 0x00, 0x22,
#endif // defined(DBCS) && defined(_MIPS_)
METAOUT+INDXOUT, // program gdc registers
GRAPH_ADDRESS_PORT,
9,0, // count, startindex
0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
0x05, 0x0F, 0xFF,
IB, // prepare atc for writing
INPUT_STATUS_1_COLOR,
METAOUT+ATCOUT, // program atc registers
ATT_ADDRESS_PORT,
21,0, // count, startindex
0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B,
0x0C, 0x0D, 0x0E, 0x0F, 0x41, 0x00,
0x0F, 0x00, 0x00,
OB, // turn video on.
ATT_ADDRESS_PORT,
0x20,
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
OWM,
GRAPH_ADDRESS_PORT,
3,
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed it for Liner addressing.
//
0x0009, 0x000a, 0x000b,
EOD
};
//
// 800x600 256-color 60Hz mode (BIOS mode 0x5C) set command string for
// CL 542x.
//
USHORT CL542x_800x600_256_60[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM, // begin setmode
SEQ_ADDRESS_PORT,
15, // count
0x100, // start sync reset
0x0101,0x0F02,0x0003,0x0E04, // program up sequencer
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed Liner addressing.
//
(LA_MASK << 12 | 0x0107),
0x0008,
0x4A0B,0x5B0C,0x450D,0x510E,
0x2B1B,0x2F1C,0x301D,0x3A1E,
OB, // point sequencer index to ff
SEQ_ADDRESS_PORT,
0x0F,
METAOUT+MASKOUT, // masked out.
SEQ_DATA_PORT,
0xDF,0x20, // and mask, xor mask
OB, // misc. register
MISC_OUTPUT_REG_WRITE_PORT,
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0xEF,
#else
0x2F,
#endif // defined(DBCS) && defined(_MIPS_)
OW, // text/graphics bit
GRAPH_ADDRESS_PORT,
0x506,
OW, // end sync reset
SEQ_ADDRESS_PORT,
0x300,
OW, // unprotect crtc 0-7
CRTC_ADDRESS_PORT_COLOR,
0x2011,
METAOUT+INDXOUT, // program crtc registers
CRTC_ADDRESS_PORT_COLOR,
28,0, // count, startindex
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0x7F, 0x63, 0x64, 0x80, 0x6B, 0x1B,
0x72, 0xF0, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x58, 0x8C,
0x57, 0x64, 0x00, 0x5F, 0x91, 0xE3,
0xFF, 0x00, 0x00, 0x22,
#else
0x7D, 0x63, 0x64, 0x80, 0x6D, 0x1C,
0x98, 0xF0, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x7B, 0x80,
0x57, 0x64, 0x00, 0x5F, 0x91, 0xe3,
0xff, 0x00, 0x00, 0x22,
#endif // defined(DBCS) && defined(_MIPS_)
METAOUT+INDXOUT, // program gdc registers
GRAPH_ADDRESS_PORT,
9,0, // count, startindex
0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
0x05, 0x0F, 0xFF,
IB, // prepare atc for writing
INPUT_STATUS_1_COLOR,
METAOUT+ATCOUT, // program atc registers
ATT_ADDRESS_PORT,
21,0, // count, startindex
0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B,
0x0C, 0x0D, 0x0E, 0x0F, 0x41, 0x00,
0x0F, 0x00, 0x00,
OB, // turn video on.
ATT_ADDRESS_PORT,
0x20,
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
OWM,
GRAPH_ADDRESS_PORT,
3,
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed it for Liner addressing.
//
0x0009, 0x000a, 0x000b,
EOD
};
//
// 800x600 256-color 72Hz mode (BIOS mode 0x5C) set command string for
// CL 542x.
//
USHORT CL542x_800x600_256_72[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM, // begin setmode
SEQ_ADDRESS_PORT,
15, // count
0x100, // start sync reset
0x0101,0x0F02,0x0003,0x0E04, // program up sequencer
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed Liner addressing.
//
(LA_MASK << 12 | 0x0107),
0x0008,
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0x4A0B,0x5B0C,0x450D,0x650E,
#else
0x4A0B,0x5B0C,0x450D,0x640E,
#endif // defined(DBCS) && defined(_MIPS_)
0x2B1B,0x2F1C,0x301D,0x3A1E,
OB, // point sequencer index to ff
SEQ_ADDRESS_PORT,
0x0F,
METAOUT+MASKOUT, // masked out.
SEQ_DATA_PORT,
0xDF,0x20, // and mask, xor mask
OB, // misc. register
MISC_OUTPUT_REG_WRITE_PORT,
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0xEF,
#else
0x2F,
#endif // defined(DBCS) && defined(_MIPS_)
OW, // text/graphics bit
GRAPH_ADDRESS_PORT,
0x506,
OW, // end sync reset
SEQ_ADDRESS_PORT,
0x300,
OW, // unprotect crtc 0-7
CRTC_ADDRESS_PORT_COLOR,
0x2011,
METAOUT+INDXOUT, // program crtc registers
CRTC_ADDRESS_PORT_COLOR,
28,0, // count, startindex
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0x7D, 0x63, 0x64, 0x80, 0x6D, 0x1C,
0x96, 0xF0, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x7B, 0x81,
0x57, 0x64, 0x00, 0x5F, 0x91, 0xE3,
0xFF, 0x00, 0x00, 0x22,
#else
0x7D, 0x63, 0x64, 0x80, 0x6D, 0x1C,
0x98, 0xF0, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x7B, 0x80,
0x57, 0x64, 0x00, 0x5F, 0x91, 0xe3,
0xff, 0x00, 0x00, 0x22,
#endif // defined(DBCS) && defined(_MIPS_)
METAOUT+INDXOUT, // program gdc registers
GRAPH_ADDRESS_PORT,
9,0, // count, startindex
0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
0x05, 0x0F, 0xFF,
IB, // prepare atc for writing
INPUT_STATUS_1_COLOR,
METAOUT+ATCOUT, // program atc registers
ATT_ADDRESS_PORT,
21,0, // count, startindex
0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B,
0x0C, 0x0D, 0x0E, 0x0F, 0x41, 0x00,
0x0F, 0x00, 0x00,
OB, // turn video on.
ATT_ADDRESS_PORT,
0x20,
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
OWM,
GRAPH_ADDRESS_PORT,
3,
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed it for Liner addressing.
//
0x0009, 0x000a, 0x000b,
EOD
};
//
// 1024x768 256-color 60Hz mode (BIOS mode 0x60) set command string for
// CL 542x.
//
USHORT CL542x_1024x768_256_60[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM, // begin setmode
SEQ_ADDRESS_PORT,
15, // count
0x100, // start sync reset
0x0101,0x0F02,0x0003,0x0E04, // program up sequencer
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed Liner addressing.
//
(LA_MASK << 12 | 0x0107),
0x0008,
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0x4A0B, 0x5B0C, 0x450D, 0x760E,
0x2B1B, 0x2F1C, 0x301D, 0x341E,
#else
0x4A0B, 0x5B0C, 0x450D, 0x3B0E,
0x2B1B, 0x2F1C, 0x301D, 0x1A1E,
#endif // defined(DBCS) && defined(_MIPS_)
OB, // point sequencer index to ff
SEQ_ADDRESS_PORT,
0x0F,
METAOUT+MASKOUT, // masked out.
SEQ_DATA_PORT,
0xDF,0x20, // and mask, xor mask
OB, // misc. register
MISC_OUTPUT_REG_WRITE_PORT,
0xEF,
OW, // text/graphics bit
GRAPH_ADDRESS_PORT,
0x506,
OW, // end sync reset
SEQ_ADDRESS_PORT,
0x300,
OW, // unprotect crtc 0-7
CRTC_ADDRESS_PORT_COLOR,
0x2011,
METAOUT+INDXOUT, // program crtc registers
CRTC_ADDRESS_PORT_COLOR,
28,0, // count, startindex
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0xA3, 0x7F, 0x80, 0x86, 0x85, 0x96,
0x24, 0xFD, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x02, 0x88,
0xFF, 0x80, 0x00, 0x00, 0x24, 0xE3,
0xFF, 0x4A, 0x00, 0x22,
#else
0xA3, 0x7F, 0x80, 0x86, 0x85, 0x96,
0x24, 0xFD, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x02, 0x88,
0xFF, 0x80, 0x00, 0x00, 0x24, 0xe3,
0xff, 0x4A, 0x00, 0x22,
#endif // defined(DBCS) && defined(_MIPS_)
METAOUT+INDXOUT, // program gdc registers
GRAPH_ADDRESS_PORT,
9,0, // count, startindex
0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
0x05, 0x0F, 0xFF,
IB, // prepare atc for writing
INPUT_STATUS_1_COLOR,
METAOUT+ATCOUT, // program atc registers
ATT_ADDRESS_PORT,
21,0, // count, startindex
0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B,
0x0C, 0x0D, 0x0E, 0x0F, 0x41, 0x00,
0x0F, 0x00, 0x00,
OB, // turn video on.
ATT_ADDRESS_PORT,
0x20,
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
OWM,
GRAPH_ADDRESS_PORT,
3,
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed it for Liner addressing.
//
0x0009, 0x000a, 0x000b,
EOD
};
//
// 1024x768 256-color 70Hz mode (BIOS mode 0x60) set command string for
// CL 542x.
//
USHORT CL542x_1024x768_256_70[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM, // begin setmode
SEQ_ADDRESS_PORT,
15, // count
0x100, // start sync reset
0x0101,0x0F02,0x0003,0x0E04, // program up sequencer
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed Liner addressing.
//
(LA_MASK << 12 | 0x0107),
0x0008,
0x4A0B, 0x5B0C, 0x450D, 0x6E0E,
0x2B1B, 0x2F1C, 0x301D, 0x2A1E,
OB, // point sequencer index to ff
SEQ_ADDRESS_PORT,
0x0F,
METAOUT+MASKOUT, // masked out.
SEQ_DATA_PORT,
0xDF,0x20, // and mask, xor mask
OB, // misc. register
MISC_OUTPUT_REG_WRITE_PORT,
0xEF,
OW, // text/graphics bit
GRAPH_ADDRESS_PORT,
0x506,
OW, // end sync reset
SEQ_ADDRESS_PORT,
0x300,
OW, // unprotect crtc 0-7
CRTC_ADDRESS_PORT_COLOR,
0x2011,
METAOUT+INDXOUT, // program crtc registers
CRTC_ADDRESS_PORT_COLOR,
28,0, // count, startindex
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0xA1, 0x7F, 0x80, 0x86, 0x85, 0x96,
0x24, 0xFD, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x02, 0x88,
0xFF, 0x80, 0x00, 0x00, 0x24, 0xE3,
0xFF, 0x4A, 0x00, 0x22,
#else
0xA3, 0x7F, 0x80, 0x86, 0x85, 0x96,
0x24, 0xFD, 0x00, 0x60, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x02, 0x88,
0xFF, 0x80, 0x00, 0x00, 0x24, 0xe3,
0xff, 0x4A, 0x00, 0x22,
#endif // defined(DBCS) && defined(_MIPS_)
METAOUT+INDXOUT, // program gdc registers
GRAPH_ADDRESS_PORT,
9,0, // count, startindex
0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
0x05, 0x0F, 0xFF,
IB, // prepare atc for writing
INPUT_STATUS_1_COLOR,
METAOUT+ATCOUT, // program atc registers
ATT_ADDRESS_PORT,
21,0, // count, startindex
0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B,
0x0C, 0x0D, 0x0E, 0x0F, 0x41, 0x00,
0x0F, 0x00, 0x00,
OB, // turn video on.
ATT_ADDRESS_PORT,
0x20,
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
OWM,
GRAPH_ADDRESS_PORT,
3,
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed it for Liner addressing.
//
0x0009, 0x000a, 0x000b,
EOD
};
//
// 1024x768 256-color 87Hz mode (BIOS mode 0x60) set command string for
// CL 542x. (Interlaced)
//
USHORT CL542x_1024x768_256_87[] = {
OWM, // begin setmode
SEQ_ADDRESS_PORT,
2, // count
0x1206, // enable extensions
0x0012,
OWM, // begin setmode
SEQ_ADDRESS_PORT,
15, // count
0x100, // start sync reset
0x0101,0x0F02,0x0003,0x0E04, // program up sequencer
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed Liner addressing.
//
(LA_MASK << 12 | 0x0107),
0x0008,
0x4A0B, 0x5B0C, 0x450D, 0x550E,
0x2B1B, 0x2F1C, 0x301D, 0x361E,
OB, // point sequencer index to ff
SEQ_ADDRESS_PORT,
0x0F,
METAOUT+MASKOUT, // masked out.
SEQ_DATA_PORT,
0xDF,0x20, // and mask, xor mask
OB, // misc. register
MISC_OUTPUT_REG_WRITE_PORT,
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0xEF,
#else
0x2F,
#endif // defined(DBCS) && defined(_MIPS_)
OW, // text/graphics bit
GRAPH_ADDRESS_PORT,
0x506,
OW, // end sync reset
SEQ_ADDRESS_PORT,
0x300,
OW, // unprotect crtc 0-7
CRTC_ADDRESS_PORT_COLOR,
0x2011,
METAOUT+INDXOUT, // program crtc registers
CRTC_ADDRESS_PORT_COLOR,
28,0, // count, startindex
//
// NOTE(DBCS) : Update 94/10/26 - NEC Corporation
//
// - Set Mode Type is VESA compatible.
//
#if defined(DBCS) && defined(_MIPS_)
0x99, 0x7F, 0x80, 0x86, 0x83, 0x99,
0x96, 0x1F, 0x00, 0x40, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x7F, 0x83,
0x7F, 0x80, 0x00, 0x7F, 0x12, 0xE3,
0xff, 0x4A, 0x01, 0x22,
#else
0xA3, 0x7F, 0x80, 0x86, 0x85, 0x96,
0xBE, 0x1F, 0x00, 0x40, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x81, 0x84,
0x7F, 0x80, 0x00, 0x80, 0x12, 0xE3,
0xff, 0x4A, 0x01, 0x22,
#endif // defined(DBCS) && defined(_MIPS_)
METAOUT+INDXOUT, // program gdc registers
GRAPH_ADDRESS_PORT,
9,0, // count, startindex
0x00, 0x00, 0x00, 0x00, 0x00, 0x40,
0x05, 0x0F, 0xFF,
IB, // prepare atc for writing
INPUT_STATUS_1_COLOR,
METAOUT+ATCOUT, // program atc registers
ATT_ADDRESS_PORT,
21,0, // count, startindex
0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B,
0x0C, 0x0D, 0x0E, 0x0F, 0x41, 0x00,
0x0F, 0x00, 0x00,
OB, // turn video on.
ATT_ADDRESS_PORT,
0x20,
OB,
DAC_PIXEL_MASK_PORT,
0xFF,
OWM,
GRAPH_ADDRESS_PORT,
3,
//
// The Miniport Driver for R96 machine is Liner addressing mode.
// This set command was changed it for Liner addressing.
//
0x0009, 0x000a, 0x000b,
EOD
};
#endif // defined(DBCS) && defined(_MIPS_)
#endif
