1 files changed, 13 insertions, 12 deletions

diff --git a/examples/Alert_Window_Mode/Alert_Window_Mode.ino b/examples/Alert_Window_Mode/Alert_Window_Mode.ino
index a68b684..0a099ad 100644
--- a/examples/Alert_Window_Mode/Alert_Window_Mode.ino
+++ b/examples/Alert_Window_Mode/Alert_Window_Mode.ino
@@ -6,7 +6,8 @@
 * mode. You can change the mode with the function setAlertModeAndLimit_V

 *  

 * Further information can be found on:

-* https://wolles-elektronikkiste.de/ads1115

+* https://wolles-elektronikkiste.de/ads1115 (German)

+* https://wolles-elektronikkiste.de/en/ads1115-a-d-converter-with-amplifier (English)

 * 

 ***************************************************************************/

 

@@ -57,7 +58,7 @@ void setup() {
    */

   adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change range

 

-  /* Set number of conversions out of limit after which the alert pin will be active

+  /* Set number of conversions out of limit after which alert pin asserts

    * - or you can disable the alert (including conversion ready alert)

    *  

    *  ADS1115_ASSERT_AFTER_1  -> after 1 conversion

@@ -88,10 +89,10 @@ void setup() {
    */

   adc.setMeasureMode(ADS1115_CONTINUOUS); //comment or change you want to change to single shot

 

-   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 

-   *  be active when measured values are beyond the maximum limit or outside the window 

+   /* Choose maximum limit or maximum and minimum alert limit (window) in volts - alert pin will 

+   *  assert when measured values are beyond the maximum limit or outside the window 

    *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)

-   *  In max limit mode the minimum value is the limit where the alert pin will be deactivated 

+   *  In max limit mode the minimum value is the limit where the alert pin assertion is cleared 

    *  again (if not latched!)  

    * 

    *  ADS1115_MAX_LIMIT

@@ -100,9 +101,9 @@ void setup() {
    */

   adc.setAlertModeAndLimit_V(ADS1115_WINDOW, 3.0, 1.5); //you can change modes / limits

   

-  /* Enable or disable latch. If latch is enabled the alarm pin will be active until the

-   * conversion register is read (getResult functions). If disabled the alarm pin will be

-   * deactivated with next value within limits. 

+  /* Enable or disable latch. If latch is enabled the alert pin will assert until the

+   * conversion register is read (getResult functions). If disabled the alert pin assertion

+   * will be cleared with next value within limits. 

    *  

    *  ADS1115_LATCH_DISABLED (default)

    *  ADS1115_LATCH_ENABLED

@@ -111,16 +112,16 @@ void setup() {
 

   /* Sets the alert pin polarity if active:

    *  

-   * Enable or disable latch. If latch is enabled the alarm pin will be active until the

-   * conversion register is read (getResult functions). If disabled the alarm pin will be

-   * deactivated with next value within limits. 

+   * Enable or disable latch. If latch is enabled the alert pin will assert until the

+   * conversion register is read (getResult functions). If disabled the alert pin assertion 

+   * will be cleared with next value within limits. 

    *  

    * ADS1115_ACT_LOW  ->  active low (default)   

    * ADS1115_ACT_HIGH ->  active high

    */

   //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default

  

-  /* With this function the alert pin will be active, when a conversion is ready.

+  /* With this function the alert pin will assert, when a conversion is ready.

    * In order to deactivate, use the setAlertLimit_V function  

    */

   //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default