diff options
| -rw-r--r-- | _ont/ont-nokia-g-010s-p-ymodem.md | 18 | ||||
| -rw-r--r-- | _ont/ont-nokia-g-010s-p.md | 318 | ||||
| -rw-r--r-- | assets/img/g-010s-p.jpg | bin | 467353 -> 69869 bytes | |||
| -rw-r--r-- | assets/img/o-010s-p.jpg | bin | 0 -> 467353 bytes |
4 files changed, 333 insertions, 3 deletions
diff --git a/_ont/ont-nokia-g-010s-p-ymodem.md b/_ont/ont-nokia-g-010s-p-ymodem.md new file mode 100644 index 0000000..683dbcf --- /dev/null +++ b/_ont/ont-nokia-g-010s-p-ymodem.md @@ -0,0 +1,18 @@ +--- +title: Flash firmware for Nokia G-010S-P (with root) +has_children: false +parent: Nokia G-010S-P +layout: default +--- + +This procedure flashes the firmware in the stick via serial. You have to get firmware to flash, some are listed on the [Huawei MA5671A page](/ont-huawei-ma5671a). + +{: .text-center .fs-6 } +<button id="flash-start-button" class="btn btn-blue" data-jtd-toggle="modal" data-jtd-target="#flash-modal">Start flash!</button> + +<div id="flash-browser-error" style="display:none">{% include alert.html content="This browser is not compatible with the web-root procedure. See the <a href='https://developer.mozilla.org/en-US/docs/Web/API/Web_Serial_API#browser_compatibility'>Browser compatibility</a>" alert="Note" icon="svg-warning" color="red" %}</div> +<noscript> +{% include alert.html content="Your browser does not support JavaScript!" alert="Note" icon="svg-warning" color="red" %} +</noscript> + +{% include ymodem_lantiq.html modelName="Nokia G-010S-P" %} diff --git a/_ont/ont-nokia-g-010s-p.md b/_ont/ont-nokia-g-010s-p.md index 7d9b6d7..0daa460 100644 --- a/_ont/ont-nokia-g-010s-p.md +++ b/_ont/ont-nokia-g-010s-p.md @@ -1,6 +1,6 @@ --- title: Nokia G-010S-P -has_children: false +has_children: true layout: default parent: Nokia --- @@ -12,7 +12,7 @@ parent: Nokia | Vendor/Brand | Nokia | | Model | G-010S-P | | ODM | SourcePhotonics | -| ODM Product Code | | +| ODM Product Code | SPS-34-24T-HP-TDFO | | Chipset | Lantiq PEB98035 | | Flash | 16 MB | | RAM | 64 MB | @@ -21,7 +21,7 @@ parent: Nokia | System | OpenWRT | | HSGMII | Yes | | Optics | SC/APC | -| IP address | | +| IP address | 192.168.1.10 | | Web Gui | Can be enabled | | SSH | ✅ user `ONTUSER`, password `SUGAR2A041` | | Telnet | | @@ -47,6 +47,10 @@ parent: Nokia The [Nokia G-010S-A](/ont-nokia-g-010s-a) can be flashed with the Nokia G-010S-P firmware, provided the MTD layout has been changed beforehand to match the new one. For the full procedure, see the post on [lafibre.info](https://lafibre.info/remplacer-livebox/guide-de-connexion-fibre-directement-sur-un-routeur-voire-meme-en-2gbps/msg870551/#msg870551) +## List of software versions + +- 3FE56853AOPD39 + ## Serial The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be accessed from the SFP connector. @@ -64,6 +68,28 @@ The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be a ## List of partitions +Partition layouts change depending on which image is booted, in particular: + +When booting image0: +``` +mtd2 ---> image0 (linux) +mtd5 --> image1 +mtd3 --> rootfs +mtd4 --> rootfs_data +``` +When booting image0: +``` +mtd2 ---> image0 +mtd3 --> image1 (linux) +mtd4 --> rootfs +mtd5 --> rootfs_data +``` + +For more info [XPONos partition layout](https://github.com/XPONos/linux_lantiq-falcon/commit/456f68f69a84c846a542a9f0ea47c37476535dcb). + + +### When booting from image0 + | dev | size | erasesize | name | | ---- | -------- | --------- | ------------- | | mtd0 | 00040000 | 00010000 | "uboot" | @@ -73,21 +99,307 @@ The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be a | mtd4 | 00370000 | 00010000 | "rootfs_data" | | mtd5 | 00800000 | 00010000 | "image1" | +### When booting from image1 + +| dev | size | erasesize | name | +| ---- | -------- | --------- | ------------- | +| mtd0 | 00040000 | 00010000 | "uboot" | +| mtd1 | 00080000 | 00010000 | "uboot_env" | +| mtd2 | 00740000 | 00010000 | "image0" | +| mtd3 | 00800000 | 00010000 | "linux" | +| mtd4 | 006d8077 | 00010000 | "rootfs" | +| mtd5 | 00410000 | 00010000 | "rootfs_data" | + # General Settings and Useful Commands +## Bootloader unlock from shell +{% include alert.html content="It is strongly recommended that you unlock the bootloader before making any major changes to the firmware." alert="Warning" icon="svg-warning" color="yellow" %} +```sh +fw_setenv bootdelay 5 +fw_setenv asc0 0 +fw_setenv preboot "gpio set 3;gpio input 2;gpio input 105;gpio input 106;gpio input 107;gpio input 108" +``` + +{% include alert.html content="In general, the last command is not needed because by default serial is already enabled on SFP PINs." alert="Info" icon="svg-info" color="blue" %} + +## Emergency bootloader unlock via TTL serial + +{% include alert.html content="This is not necessary if you have already unlocked the bootloader from the shell as specified above." alert="Warning" icon="svg-warning" color="yellow" %} + +If for some reason you are in the situation where you do not have a bootable firmware on your SFP stick you can do an emergency unlock via TTL serial. + +To perform the emergency unlock is necessary to have: +- TTL-USB adapter +- SFP adapter to connect the TTL-USB cables to the SFP stick + +The electrical connections are the same as those of the Huawei MA5671A, see the [Huawei root guide](/ont-huawei-ma5671a-root-web) for accurate details on how to connect the TTL-USB to the SFP adapter. + +When you are ready with everything plugged in you need to press the button below. A window will open that will execute the emergency unlock. + +{: .text-center .fs-6 } +<button id="start-button" class="btn btn-blue" data-jtd-toggle="modal" data-jtd-target="#root-modal" disabled>Start emergency unlock!</button> +{% include root_lantiq.html modelName="Nokia G-010S-P" unlockHuaweiShell=false %} + +<div id="browser-error" style="display:none">{% include alert.html content="This browser is not compatible with the emergency unlock procedure. See the <a href='https://developer.mozilla.org/en-US/docs/Web/API/Web_Serial_API#browser_compatibility'>Browser compatibility</a>" alert="Note" icon="svg-warning" color="red" %}</div> +<noscript> +{% include alert.html content="Your browser does not support JavaScript!" alert="Note" icon="svg-warning" color="red" %} +</noscript> + + +## Getting and Setting S/N +To check the current serial number: +```sh +onu gtcsng +``` + +To set the current serial number: +```sh +onu gtcsns ABCD12345678 +``` + +## Getting and Setting PLOAM Password +To check the current password (the password field contains decimal values of ASCII characters): +```sh +onu gtccg +``` + +To set the current password: +```sh +uci set gpon.ploam.nPassword="0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39" +uci commit +``` + +{% include alert.html content="There is also the `onu gtc_password_set` command to set the ploam password but it does not seem to work." alert="Info" icon="svg-info" color="blue" %} + +The `link_status` value shows the speed. + ## Disabling Dying Gasp ```sh fw_setenv nDyingGaspEnable 0 ``` +## Rebooting the ONU +```sh +reboot +``` + +## Checking whether the connection with the OLT was successful (O5 state) + +```sh +onu ploamsg +``` + ## Enabling the Web UI To activate the web-ui you can use the following guide on [dslreport](https://www.dslreports.com/forum/r32458588-). +## Transferring files to the stick + +{% include alert.html content="If you use a modern OpenSSH version (e.g. >= 8.8) you will have to use the legacy protocol and enable some deprecated algorithms: scp `-oKexAlgorithms=+diffie-hellman-group1-sha1 -oHostKeyAlgorithms=+ssh-dss [...]`" alert="Info" icon="svg-info" color="blue" %} + +```sh +# scp rootfs.bin root@192.168.1.10:/tmp/ +``` + +## Backup of all partition + +Make a backup of all partitions, an easy way is: +- On the stick run: +```sh +cat /proc/mtd +``` +- For each mtdX run in the lantiq shell: +```sh +cp /dev/mtdX /tmp +``` + +{% include alert.html content="If you use a modern OpenSSH version (e.g. >= 8.8) you will have to use the legacy protocol and enable some deprecated algorithms: `scp -oKexAlgorithms=+diffie-hellman-group1-sha1 -oHostKeyAlgorithms=+ssh-dss [...]`" alert="Info" icon="svg-info" color="blue" %} + +And in the computer shell: +```sh +scp ONTUSER@192.168.1.10:/tmp/mtdX ./ +``` + +## Checking the currently active image + +```sh +# fw_printenv committed_image +``` + +## Booting to a different image + + +```sh +# fw_setenv committed_image 0|1 +# fw_setenv image0|1_is_valid 1 +``` + +## Cloning of mtd1 (image 0) into mtd5 (image 1) + +{% include alert.html content="Image 0 can be flashed to image 1, while image 1 cannot be flashed to image 0 because it has larger rootfs_data" alert="Warning" icon="svg-warning" color="yellow" %} + +The following commands are used to clone image0 to image1 and then boot to it +```sh +# cat /dev/mtd2 > /tmp/mtd2.bin +# mtd -e image1 write /tmp/mtd2.bin image1 +# fw_setenv committed_image 1 +# fw_setenv image1_is_valid 1 +# reboot +``` + +## Flashing a new rootfs via SSH + +{% include alert.html content="Only the inactive image can be flashed" alert="Info" icon="svg-info" color="blue" %} + +The following commands are used to flash a new rootfs to image1 and then boot to it +```sh +# mtd -e image1 write /tmp/rootfs.bin image1 +# fw_setenv committed_image 1 +# fw_setenv image1_is_valid 1 +# reboot +``` + +{% include alert.html content="Some OLTs don't like when ONTs don't boot from image 0, therefore the previous procedure must be preceded by the following procedure with inverted images, as to clone image 1 into image 0" alert="Warning" icon="svg-warning" color="yellow" %} + +## Flashing a new rootfs via Serial + +If you wish to change the firmware via serial, we recommend using the web app: [Web Serial Flash](/ont-nokia-g-010s-p-ymodem) + +## TX Fault / Serial + +The stick stays in a perpetual "TX Fault" state since the same SFP pin is used for both serial and TX Fault signaling, if that causes you issues (normally it shouldn't) you can issue the commands below to disable it. Note that it will disable both the TX Fault signal and Serial on the stick after boot. + +```sh +fw_setenv asc0 1 +fw_setenv preboot "gpio set 3;gpio input 100;gpio input 105;gpio input 106;gpio input 107;gpio input 108" +``` + +In case you need to re-enable it issue the following commands from the bootloader (FALCON) + +```sh +FALCON => setenv asc0 0 +FALCON => saveenv +``` + +## Getting/Setting Speed LAN Mode + +| Velue | Speed | +| ----- | ---------------------------------- | +| 4 | 1 Gbps / SGMII | +| 5 | 2.5 Gbps / HSGMII with auto-neg on | + +To enable the 2.5 Gbps / HSGMII with auto-neg on: + +```sh +fw_setenv sgmii_mode 5 +``` + +To remove the value (back to default): +```sh +fw_setenv sgmii_mode +``` + +To get the (H)SGMII Mode: + +```sh +onu lanpsg 0 +``` +The `link_status` variable tells the current speed + +## Querying a particular OMCI ME +```sh +omci_pipe.sh meg MIB_IDX ME_IN +``` +Where `MIB_IDX` is the MIB ID and the `ME_IN` is the ME instance number + +# EEPROM (I2C slave simulated EEPROM) + +The Nokia G-010S-P does not have a physical EEPROM, the Falcon SOC emulates an EEPROM by exposing it on the I2C interface as required by the SFF-8472 specification. + +On the I2C interface there will be two memories of 256 bytes each at the addresses `1010000X (A0h)` and `1010001X (A2h)`. + +The Zyxel PMG3000-D20B stores the content of the emulated EEPROM1 (A2h) in Boot env variable `sfp_a2_info` to restore it after a reboot. + +{% include alert.html content="The contents of EEPROM0 (A0h) are not stored anywhere and is regenerated at each boot" alert="Info" icon="svg-info" color="blue" %} + +## EEPROM1 layout + +| address | size | name | default value | description | +| ------- | ---- | --------------------------------- | ----------------------------------------- | ----------------------------------------------------------- | +| | | **DIAGNOSTIC AND CONTROL FIELDS** | | | +| 0-1 | 2 | Temp High Alarm | `0x64 0x00` (100℃) | Value expressed in two's complement | +| 2-3 | 2 | Temp Low Alarm | `0xCE 0x00` (-50℃) | Value expressed in two's complement | +| 4-5 | 2 | Temp High Warning | `0x5F 0x00` (95℃) | Value expressed in two's complement | +| 6-7 | 2 | Temp Low Warning | `0xD8 0x00` (-40℃) | Value expressed in two's complement | +| 8-9 | 2 | Voltage High Alarm | `0x8C 0xA0` (3.6V) | Value expressed in volt subunits[^subunit] | +| 10-11 | 2 | Voltage Low Alarm | `0x75 0x30` (3V) | Value expressed in volt subunits[^subunit] | +| 12-13 | 2 | Voltage High Warning | `0x88 0xB8` (3.5V) | Value expressed in volt subunits[^subunit] | +| 14-15 | 2 | Voltage Low Warning | `0x79 0x18` (3.1V) | Value expressed in volt subunits[^subunit] | +| 16-17 | 2 | Bias High Alarm | `0xAF 0xC8` (4.5mA) | Value expressed in milliampere subunits[^subunit] | +| 18-19 | 2 | Bias Low Alarm | `0x00 0x00` (0mA) | Value expressed in milliampere subunits[^subunit] | +| 20-21 | 2 | Bias High Warning | `0x88 0xB8` (3.5mA) | Value expressed in milliampere subunits[^subunit] | +| 22-23 | 2 | Bias Low Warning | `0x00 0x00` (0mA) | Value expressed in milliampere subunits[^subunit] | +| 24-25 | 2 | TX Power High Alarm | `0x7B 0x86` (5dBm) | Value expressed in watts subunits[^subunit] | +| 26-27 | 2 | TX Power Low Alarm | `0x22 0xD0` (-0dBm) | Value expressed in watts subunits[^subunit] | +| 28-29 | 2 | TX Power High Warning | `0x6E 0x17` (4dBm) | Value expressed in watts subunits[^subunit] | +| 30-31 | 2 | TX Power Low Warning | `0x27 0x10` (0dBm) | Value expressed in watts subunits[^subunit] | +| 32-33 | 2 | RX Power High Alarm | `0x07 0xCB` (-7dBm) | Value expressed in watts subunits[^subunit] | +| 34-35 | 2 | RX Power Low Alarm | `0x00 0x0F` (-28dBm) | Value expressed in watts subunits[^subunit] | +| 36-37 | 2 | RX Power High Warning | `0x06 0x30` (-8dBm) | Value expressed in watts subunits[^subunit] | +| 38-39 | 2 | RX Power Low Warning | `0x00 0x14` (-27dBm) | Value expressed in watts subunits[^subunit] | +| 40-45 | 6 | MAC address | Unique in each SFP | Contains the mac address of the SFP, it could also be empty | +| 46-55 | 10 | Reserved | `0x00 0x00 0x00...` | Reserved | +| 56-59 | 4 | RX_PWR(4) Calibration | `0x00 0x00 0x00 0x00` | 4th order RSSI calibration coefficient | +| 60-63 | 4 | RX_PWR(3) Calibration | `0x00 0x00 0x00 0x00` | 3rd order RSSI calibration coefficient | +| 64-67 | 4 | RX_PWR(2) Calibration | `0x00 0x00 0x00 0x00` | 2nd order RSSI calibration coefficient | +| 68-71 | 4 | RX_PWR(1) Calibration | `0x3F 0x80 0x00 0x00` | 1st order RSSI calibration coefficient | +| 72-75 | 4 | RX_PWR(0) Calibration | `0x00 0x00 0x00 0x00` | 0th order RSSI calibration coefficient | +| 76-77 | 2 | TX_I(Slope) Calibration | `0x01 0x00` | Slope for Bias calibration | +| 78-79 | 2 | TX_I(Offset) Calibration | `0x00 0x00` | Offset for Bias calibration | +| 80-81 | 2 | TX_PWR(Slope) Calibration | `0x01 0x00` | Slope for TX Power calibration | +| 82-83 | 2 | TX_PWR(Offset) Calibration | `0x00 0x00` | Offset for TX Power calibration | +| 84-85 | 2 | T(Slope) Calibration | `0x01 0x00` | Slope for Temperature calibration | +| 86-87 | 2 | T(Offset) Calibration | `0x00 0x00` | Offset for Temperature calibration, in units of 256ths °C | +| 88-89 | 2 | V(Slope) Calibration | `0x01 0x00` | Slope for VCC calibration | +| 90-91 | 2 | V(Offset) Calibration | `0x00 0x00` | Offset for VCC calibration | +| 92-94 | 3 | Reserved | `0x00 0x00 0x00` | Reserved | +| 95 | 1 | CC_DMI | | Check code for Base Diagnostic Fields (addresses 0 to 94) | +| 96 | 1 | Temperature MSB | | Internally measured module temperature | +| 97 | 1 | Temperature LSB | | | +| 98 | 1 | Vcc MSB | | Internally measured supply voltage in transceiver | +| 99 | 1 | Vcc LSB | | | +| 100 | 1 | TX Bias MSB | | Internally measured TX Bias Current | +| 101 | 1 | TX Bias LSB | | | +| 102 | 1 | TX Power MSB | | Measured TX output power | +| 103 | 1 | TX Power LSB | | | +| 104 | 1 | RX Power MSB | | Measured RX input power | +| 105 | 1 | RX Power LSB | | | +| 106-109 | 4 | Optional Diagnostics | `0xFF 0xFF 0xFF 0xFF` (No support) | Monitor Data for Optional Laser temperature and TEC current | +| 110 | 1 | Status/Control | `0x03` | Optional Status and Control Bits | +| 111 | 1 | Reserved | `0x00` | Reserved | +| 112-113 | 2 | Alarm Flags | Supported | Diagnostic Alarm Flag Status Bits | +| 114 | 1 | Tx Input EQ control | `0xFF` (No support) | Tx Input equalization level control | +| 115 | 1 | Rx Out Emphasis control | `0xFF` (No support) | Rx Output emphasis level control | +| 116-117 | 2 | Warning Flags | Supported | Diagnostic Warning Flag Status Bits | +| 118-119 | 2 | Ext Status/Control | `0x00 0x00` | Extended module control and status bytes | +| | | **GENERAL USE FIELDS** | | | +| 120-126 | 7 | Vendor Specific | `0x70 0x00 0x00 0x00 0x00 0x00 0x20` | Vendor specific memory addresses | +| 127 | 1 | Table Select | `0x00` | Optional Page Select | +| | | **USER WRITABLE EEPROM** | | | +| 128-247 | 120 | Reserved | `0x00 0x00 0x00...` | Reserved | +| 248-255 | 8 | Vendor Control | `0x00 0x00 0x00 0x00 0x00 0x41 0x41 0x31` | Vendor specific control functions | + +{% include alert.html content="For more information, see the SFF-8472 Rev 11.0 specification." alert="Info" icon="svg-info" color="blue" %} + + # Miscellaneous Links - [alcatel_lucent-lantiq_falcon](https://github.com/minhng99/alcatel_lucent-lantiq_falcon) - [uboot lantiq falcon](https://github.com/minhng99/u-boot_lantiq_falcon) - [Usage GPON module SFP in Spain](https://forum.mikrotik.com/viewtopic.php?t=116364&start=300) +--- + +[^subunit]: The subunit are 10000 times smaller than the specified unit + diff --git a/assets/img/g-010s-p.jpg b/assets/img/g-010s-p.jpg Binary files differindex f3a863f..60300a6 100644 --- a/assets/img/g-010s-p.jpg +++ b/assets/img/g-010s-p.jpg diff --git a/assets/img/o-010s-p.jpg b/assets/img/o-010s-p.jpg Binary files differnew file mode 100644 index 0000000..f3a863f --- /dev/null +++ b/assets/img/o-010s-p.jpg |
