diff options
Diffstat (limited to '_ont_xgs/serial_dump/fs-XGS-ONU-25-20NI_minishell.txt')
| -rw-r--r-- | _ont_xgs/serial_dump/fs-XGS-ONU-25-20NI_minishell.txt | 208 |
1 files changed, 208 insertions, 0 deletions
diff --git a/_ont_xgs/serial_dump/fs-XGS-ONU-25-20NI_minishell.txt b/_ont_xgs/serial_dump/fs-XGS-ONU-25-20NI_minishell.txt new file mode 100644 index 0000000..08d22d0 --- /dev/null +++ b/_ont_xgs/serial_dump/fs-XGS-ONU-25-20NI_minishell.txt @@ -0,0 +1,208 @@ ++traffic Service CLI menu + +ces CES CLI menu (empty) + +pon PON CLI menu + +debug PON debug command + rptwanstat config report wan status to MEC + tcont add/delete/flush a Tcont + flow configure the parameters of a flow + queue configure the parameters of a Tcont Queue + sendomci Send a OMCI message + prbs Enable/disable transmitting PRBS continuously + dyingGsend Enable/disable transmitting PRBS continuously + omcidbg Enable/disable kernel OMCI log + reportGemCnt Enable/disable report gem counter to MEC + throughput Enable/disable throughput test + ponmode Enable/disable qos + dump_classifier Dump classifier rule + gem_to_cpu trap gem port all packets to cpu + +hw PON Hardware level command + show Show hardware status or configurations + read_reg Read register value + write_reg Write register value + +ca PON cortina command + show Show cortina status or configurations + +app PON APP command + show Show database in PMR app + sendmsg Send Msg to PMR app + ber_interval Configure the BER interval + sf_threshold The threshold of BIP to report signal failure + sd_threshold The threshold of BIP to report signal degrade + sn Set the serial number of the ONT + password Set the password of ONT + to1_to2 Set the To1 To2 timer of ONT + show show PON information + +eth ETH CLI menu + +debug Ethernet Debug System CLI menu + pack Ethernet CLI debug function for pack driver + brdg Ethernet CLI debug function for SOC bridge + phy Ethernet CLI debug function for PHY + showconn Show ethernet connection debug info + ethdbg enable/disable the eth debug flag + show Ethernet CLI Show + +voip VoIP CLI menu (empty) + +omci omci CLI menu + +debug OMCI Debug System CLI menu + showemrcfg show the configuration of EMR from MEC + crc enable the crc check of omci message + omiterr Enable/disable omitting OMCI errors + acpower Start or stop power shedding + allocid Function call mec_AddAllocId + ponstate Function call mec_HandlePonStateChange + +voip OMCI VoIP System CLI menu + show show the configuration of VMR from MEC + +defaultxml MEC Xml List CLI menu + show show the List of default Xml from MEC + crc_commit runtime xml add crc + restore_xml runtime xml restore + show Show the information of MEC + clear Clear the runtime data + +router router CLI menu (empty) + +dmr DMR CLI menu (empty) + +hpna HPNA CLI menu (empty) ++system System CLI menu + +mib MIB CLI menu + +debug MIB Debug System CLI menu + dump Dump current mib to a file + reset Reset mib to default values + show Show the content of mib tables + +log LOG CLI menu + +kernel KERNEL LOG CLI menu (empty) + show Print out a log + dump dump the content of a log file + set Save a log to a file + clear Clear a log + collectlog Collectlog all log + +env ENV CLI menu + show Print out enviroment variables + +misc MISC CLI menu + +bob BOSA CLI menu + eep Misc CLI Show + unlock Misc CLI Show + echo Misc CLI Show + 2090 Misc CLI Show + preheat Misc CLI Show + auto Misc CLI Show + automod Misc CLI Show + restart Misc CLI Show + +debug Misc Debug System CLI menu + showwc Show write counter of mtd device + showbad Show bad blocks of mtd device + show Misc CLI Show + rf Misc CLI Show + filter Misc CLI Show + agc Misc CLI Show + ponalarm Misc CLI Show + mpcode Read or write eeprom : EEP_MFG_PRODUCTCODE + mpsn Read or write eeprom : EEP_MFG_PRODUCTSERIAL + mhwv Read or write eeprom : EEP_MFG_HWVERSION + lasersn Read or write eeprom : EEP_MFG_LASERSERIAL + mac1 Read or write eeprom : EEP_MFG_MAC1 + mac2 Read or write eeprom : EEP_MFG_MAC2 + eepver Read or write eeprom : EEP_MFG_EEPVER + burnin Read or write burnin flag : EEP_MFG_BURNIN + rfthigh Read or write rfthigh in unit of 64 ohm : EEP_MFG_RFT_HIGH + rftlow Read or write rftlow in unit of 64 ohm: EEP_MFG_RFT_LOW + rithigh Read or write rithigh in unit of 64 ohm : EEP_MFG_RIT_HIGH + ritlow Read or write ritlow in unit of 64 ohm: EEP_MFG_RIT_LOW + major Read or write eeprom : EEP_HW_FUNCTIONMAJOR + minor Read or write eeprom : EEP_HW_FUNCTIONMINOR + hwver Read or write eeprom : EEP_HW_VERSION + vendor Read or write eeprom : EEP_EQ_VENDORID + eqsn Read or write eeprom : EEP_EQ_SERIALNUMBER + eqsnvend Read or write eeprom : EEP_EQ_SNVENDOR + eqvid Read or write eeprom : EEP_EQ_VERSIONID + eqid Read or write eeprom : EEP_EQ_ID + img_name Read or write eeprom : EEP_SW_BOOTIMAGE + admin_ip Read or write eeprom : EEP_SW_IPADDR + admin_mask Read or write eeprom : EEP_SW_IPMASK + server_ip Read or write eeprom : EEP_SW_HOSTIPADDR + admin_gw Read or write eeprom : EEP_SW_GATEIPADDR + ftp_user Read or write eeprom : EEP_SW_FTPUSER + ftp_passwd Read or write eeprom : EEP_SW_FTPPASS + bootflag Read or write eeprom : EEP_SW_BOOTFLAG + admin_en Read or write eeprom : EEP_SW_BOOTREMOTEEN + xgspon_regid Read or write eeprom : XGS PON Registration ID + test_en Read or write eeprom : EEP_SW_BOOTTESTEN + notcomplete Read or write eeprom : EEP_SW_BOOTNOTCOMPLETE + act_img Read or write eeprom : EEP_SW_ACTIVEIMAGE + commit_img Read or write eeprom : EEP_SW_COMMITIMAGE + pon_passwd Read or write eeprom : EEP_APP_GPONPASSWORD + register_id Read or write eeprom : EEP_APP_GPONPASSWORD + hwerr Read or write eeprom : EEP_HW_DIAGNOSTICCODE + vdsl2_vendor Read or write eeprom : EEP_VDSL2_VENDORID + ssh_en Read or write eeprom : EEPROM_RW_CMD + i2c_r This command read i2c device in raw mode + i2c_w This command write i2c device in raw mode + write_mem This command is used to write otp + read_mem This command is used to read otp + sendevent This command is used to send led event directly + testloaden This command enable test load for manufacture + testensn This command enable test load for manufacture + eep_reset This command restore EEPROM factory default configuration + eep_r8 This command read EEPROM in raw mode + eep_w8 This command write EEPROM in raw mode + eep_crc This command update/check EEPROM crc value + exeep_r8 This command read EEPROM in raw mode + exeep_w8 This command write EEPROM in raw mode + exeep_crc This command update/check EEPROM crc value + eepinfo This command show eep info. + clearcfg This command is used to clear ONT runtime config , if full para is set, clear loid also!Usage: clearcfg [full] + final_check This command is used to show some important information for checking! + led This command is used to only turn on green leds,red leds or off all leds!Usage: led gon/ron/off + testloaden This command enable test load for manufacture + testensn This command enable test load for manufacture + get_gpio_val This command get gpio value + diswdt This command disable for manufacture + bosa This command is used to set bosa version and type + image_copy This command copy one image to another at next boot time + stopreboot Stop reboot command for debug + +manu Manufacture CLI menu + we This command write eeprom for manufacture + wep This command only write PC for manufacture + wes This command only write SN for manufacture + wem1 This command only write MAC1 for manufacture + wem2 This command only write MAC2 for manufacture + ledon This command turn on all led + ledoff This command turn off all led + final_check This command do final check + get_gpio_val This command get gpio value + trans This command show transceiver info + temp This command show system temperature + er This command enable rf + dr This command diable rf + ef This command enable filter + df This command disable filter + ten This command enable test load + wd This command disable watchdog + tensn This command enable test load, special for BL olt + ces_main This command configure ces connection for main test board + ces_back This command configure ces connection for backup test board + check_boot_status This command check boot status + check_ranging_statusThis command check ranging status + check_usb_port This command does manu test for USB device + reset_button_test This command is used for Reset Button test + factory_reset Clear all configuration and return to factory setting + load_certfile Load ACS HTTPS private Cert file into ONT + +fs File System CLI menu + show Show the content of system memory + supgrade super user Upgrade Image from Local Ftp Server + flash System Flash memory Operation command + upgrade Upgrade Image from Local Ftp Server + check check the content of system mtd + +net NET CLI menu + mirror Set mirror debug + dump Set dump frames debug + log Open/Close driver debug log + atconn Active connection debug + show Show NetMgr Data + +shell Shell + +debug System Debug CLI menu + showtimer Show timers + showtask Show task state + starttimer Start timers + stoptimer Start timers + md5 calculate MD5 value from input string + md5num calculate MD5 number string from input string + printlog Set the log level to print to console + ontver Show ONT Software Version + custom Get/Set ONT Software custom information
\ No newline at end of file |